Advertenties
Inhoudsopgave
29.4 Tastcycli Werkstukken automatisch controleren.......................................................................... 1646
29.4.1
Basisprincipes.......................................................................................................................................... 1646
29.4.2
cyclus 0 REFERENTIEVLAK...................................................................................................................1652
29.4.3
Cyclus 1 POLAIR NULPUNT..................................................................................................................1653
29.4.4
cyclus 420, METEN HOEK.....................................................................................................................1655
29.4.5
cyclus 421 METEN BORING..................................................................................................................1658
29.4.6
cyclus 422 MET. CIRKEL BUITEN........................................................................................................1664
29.4.7
cyclus 423 MET. RECHTHK. BINNEN.................................................................................................1670
29.4.8
cyclus 424 MET. RECHTHK BUITEN...................................................................................................1675
29.4.9
cyclus 425 METING INW. BREEDTE................................................................................................... 1680
29.4.10 Cyclus 426 METING RAND BUITEN....................................................................................................1684
29.4.11 Cyclus 427 METEN COORDINATEN....................................................................................................1687
29.4.12 Cyclus 430 METING GATENCIRKEL................................................................................................... 1692
29.4.13 Cyclus 431 METING VLAK.................................................................................................................... 1697
29.4.14 Programmeervoorbeelden..................................................................................................................... 1701
29.5 Tastcycli Speciale functies...........................................................................................................1704
29.5.1
Basisprincipes.......................................................................................................................................... 1704
29.5.2
Cyclus 3 METEN......................................................................................................................................1705
29.5.3
Cyclus 4 METEN 3D............................................................................................................................... 1707
29.5.4
Cyclus 444 TASTEN 3D......................................................................................................................... 1710
29.5.5
Cyclus 441 SNEL AANTASTEN............................................................................................................ 1716
29.5.6
Cyclus 1493 EXTRUSIE TASTEN......................................................................................................... 1718
29.6 Tastcycli Kalibratie.......................................................................................................................1721
29.6.1
Basisprincipes.......................................................................................................................................... 1721
29.6.2
Cyclus 461 TS LENGTE KALIBREREN................................................................................................ 1723
29.6.3
Cyclus 462 TS KALIBREREN IN RING.................................................................................................1725
29.6.4
Cyclus 463 TS KALIBREREN AAN TAP.............................................................................................. 1728
29.6.5
Cyclus 460 TS KALIBREREN AAN KOGEL (optie #17).................................................................... 1731
29.7 Tastcycli Kinematica automatisch meten..................................................................................... 1737
29.7.1
Basisprincipes (optie #48).....................................................................................................................1737
29.7.2
Cyclus 450 KINEMATICA OPSLAAN (optie #48).............................................................................. 1741
29.7.3
Cyclus 451 KINEMATICA OPMETEN (optie #48)............................................................................. 1744
29.7.4
cyclus 452 PRESET-COMPENSATIE (optie #48).............................................................................. 1759
29.7.5
cyclus 453 KINEMATICA ROOSTER (optie #48), (optie #52).........................................................1770
29.8 Tastcycli Gereedschappen automatisch meten............................................................................ 1777
29.8.1
Basisprincipes.......................................................................................................................................... 1777
29.8.2
cyclus 30 of 480 TT KALIBREREN...................................................................................................... 1781
29.8.3
cyclus 31 of 481 GEREEDSCH.-LENGTE............................................................................................1783
29.8.4
cyclus 32 of 482 GEREEDSCH.-RADIUS.............................................................................................1786
29.8.5
cyclus 33 of 483 GEREEDSCHAP METEN......................................................................................... 1790
29.8.6
cyclus 484 IR-TT KALIBREREN............................................................................................................ 1793
29.8.7
cyclus 485 DRAAIGEREEDSCHAP METEN (optie #50)................................................................... 1797
HEIDENHAIN | TNC7 | TNCguide | 01/2022
41
Advertenties
