Siemens SINUMERIK 840D sl Bedieningshandboek pagina 14
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (834 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (486 pagina's)
Advertenties
Inhoudsopgave
10.3.7
Contouroproep (CYCLE62) - alleen met G-code programma..............................................420
10.3.8
Verspanen (CYLCE952)......................................................................................................422
10.3.9
Verspanen rest (CYLCE952)...............................................................................................431
10.3.10
Steken (CYCLE952).............................................................................................................433
10.3.11
Steken rest (CYCLE952)......................................................................................................439
10.3.12
Steekdraaien (CYCLE952)...................................................................................................442
10.3.13
Steekdraaien rest (CYCLE952)............................................................................................448
10.4
Frezen..................................................................................................................................450
10.4.1
Vlakfrezen (CYCLE61).........................................................................................................450
10.4.2
Rechthoekige kamer (POCKET3)........................................................................................454
10.4.3
Cirkelkamer (POCKET4)......................................................................................................463
10.4.4
Rechthoekige tap (CYCLE76)..............................................................................................473
10.4.5
Cirkeltap (CYCLE77)............................................................................................................480
10.4.6
Meerkant (CYCLE79)...........................................................................................................486
10.4.7
Lengtesleuf (SLOT1)............................................................................................................491
10.4.8
Cirkelsleuf (SLOT2)..............................................................................................................501
10.4.9
Open sleuf (CYCLE899)......................................................................................................508
10.4.10
Slobgat (LONGHOLE) - alleen bij G-code programma........................................................519
10.4.11
Schroefdraadfrezen (CYCLE70)..........................................................................................521
10.4.12
Graveren (CYCLE60)...........................................................................................................525
10.5
Contourfrezen......................................................................................................................531
10.5.1
Algemeen.............................................................................................................................531
10.5.2
Weergave van de contour....................................................................................................532
10.5.3
Nieuwe contour maken........................................................................................................533
10.5.4
Contourelementen maken....................................................................................................536
10.5.5
Contour wijzigen...................................................................................................................541
10.5.6
Contouroproep (CYCLE62) - alleen met G-code programma..............................................542
10.5.7
Baanfrezen (CYCLE72).......................................................................................................543
10.5.8
Contourkamer/contourtap (CYCLE63/64)............................................................................549
10.5.9
Contourkamer voorboren (CYCLE64)..................................................................................551
10.5.10
Contourkamer frezen (CYCLE63)........................................................................................555
10.5.11
Contourkamer restmateriaal (CYCLE63, optie)...................................................................562
10.5.12
Contourtap frezen (CYCLE63).............................................................................................564
10.5.13
Contourtap restmateriaal (CYCLE63, optie)........................................................................569
10.6
Andere cycli en functies.......................................................................................................572
10.6.1
Zwenken vlak / Uitlijnen gereedschap (CYCLE800)............................................................572
10.6.2
Zwenken gereedschap (CYCLE800)...................................................................................579
10.6.2.1
Uitlijnen van draaigereedschap - alleen bij G-code programma's (CYCLE800)..................579
10.6.2.2
Uitlijnen van freesgereedschap - alleen bij G-code programma's (CYCLE800)..................583
10.6.2.3
Aanzetten van freesgereedschap - alleen bij G-code programma's (CYCLE800)...............584
10.6.3
High Speed Settings (CYCLE832).......................................................................................585
10.6.3.1
Parameters...........................................................................................................................588
10.6.4
Subprogramma's..................................................................................................................589
10.7
Andere cycli en functies ShopTurn......................................................................................591
10.7.1
Boren midden.......................................................................................................................591
10.7.2
Draad midden.......................................................................................................................595
10.7.3
Transformaties.....................................................................................................................597
10.7.4
Verschuiving.........................................................................................................................599
10.7.5
Rotatie..................................................................................................................................600
10.7.6
Schaalverdeling....................................................................................................................601
14
Bedieningshandboek, 12/2017, 6FC5398-8CP40-6JA1
Draaien
Advertenties
