Siemens SINUMERIK 840D sl Bedieningshandboek pagina 13
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (834 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (486 pagina's)
Inhoudsopgave
Advertenties
9.15
Technologische functies oproepen......................................................................................288
9.15.1
Verdere functies in de invoerschermen................................................................................288
9.15.2
Controle van cyclusparameters............................................................................................289
9.15.3
Instelgegevens voor technologische functies.......................................................................289
9.15.4
Variabelenprogrammerung..................................................................................................289
9.15.5
Cyclusoproep wijzigen.........................................................................................................290
9.15.6
Compatibiliteit bij cyclusondersteuning...............................................................................291
9.16
Cyclus voor naderen/verwijderen programmeren................................................................291
9.17
Meetcyclusondersteuning....................................................................................................293
9.18
Voorbeeld: Standaardbewerking..........................................................................................293
9.18.1
Werkstuktekening.................................................................................................................294
9.18.2
Programmering....................................................................................................................294
9.18.3
Resultaten/Simulatietest......................................................................................................306
9.18.4
G-codebewerkingsprogramma.............................................................................................308
10
Technologische functies programmeren (cycli)........................................................................................311
10.1
Boren....................................................................................................................................311
10.1.1
Algemeen.............................................................................................................................311
10.1.2
Centreren (CYCLE81)..........................................................................................................312
10.1.3
Boren (CYCLE82)................................................................................................................314
10.1.4
Ruimen (CYCLE85).............................................................................................................319
10.1.5
Kotteren (CYCLE86)............................................................................................................321
10.1.6
Diepgatboren 1 (CYCLE83).................................................................................................324
10.1.7
Diepgatboren 2 (CYCLE830)...............................................................................................329
10.1.8
Draadtappen (CYCLE84, 840).............................................................................................340
10.1.9
Draadtapfrezen (CYCLE78).................................................................................................348
10.1.10
Posities en positiepatroon....................................................................................................351
10.1.11
Posities naar keuze (CYCLE802)........................................................................................353
10.1.12
Positiepatroon Reeks (HOLES1).........................................................................................357
10.1.13
Positiepatroon Rooster of Kader (CYCLE801) ....................................................................360
10.1.14
Positiepatroon Cirkel of Cirkelboog (HOLES2)....................................................................364
10.1.15
Posities tonen en verbergen................................................................................................370
10.1.16
Posities herhalen..................................................................................................................371
10.2
Draaien.................................................................................................................................372
10.2.1
Algemeen.............................................................................................................................372
10.2.2
Verspanen (CYLCE951)......................................................................................................372
10.2.3
Groef (CYCLE930)...............................................................................................................375
10.2.4
Ondersnijding vorm E en F (CYCLE940).............................................................................378
10.2.5
Draaduitloop (CYCLE940)...................................................................................................380
10.2.6
Schroefdraad draaien (CYCLE99).......................................................................................383
10.2.7
Schroefdraadkoppeling (CYCLE98).....................................................................................400
10.2.8
Afsteken (CYCLE92)............................................................................................................406
10.3
Contourdraaien....................................................................................................................408
10.3.1
Algemeen.............................................................................................................................408
10.3.2
Weergave van de contour....................................................................................................409
10.3.3
Nieuwe contour maken........................................................................................................411
10.3.4
Contourelementen maken....................................................................................................412
10.3.5
Passingsmaat invoeren........................................................................................................418
10.3.6
Contour wijzigen...................................................................................................................420
Draaien
Bedieningshandboek, 12/2017, 6FC5398-8CP40-6JA1
Inhoudsopgave
13
Advertenties
Inhoudsopgave
