Siemens SINUMERIK 840D sl Bedieningshandboek pagina 15
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (486 pagina's)
Inhoudsopgave
Advertenties
9.1.9
Draadtapfrezen (CYCLE78).................................................................................................343
9.1.10
Posities en positiepatroon....................................................................................................347
9.1.11
Posities naar keuze (CYCLE802)........................................................................................348
9.1.12
Positiepatroon reeks (HOLES1)...........................................................................................352
9.1.13
Positiepatroon rooster of kader (CYCLE801).......................................................................353
9.1.14
Positiepatroon Cirkel of Cirkelboog (HOLES2)....................................................................355
9.1.15
Posities tonen en verbergen................................................................................................358
9.1.16
Posities herhalen..................................................................................................................359
9.2
Frezen..................................................................................................................................360
9.2.1
Vlakfrezen (CYCLE61).........................................................................................................360
9.2.2
Rechthoekige kamer (POCKET3)........................................................................................363
9.2.3
Cirkelkamer (POCKET4)......................................................................................................370
9.2.4
Rechthoekige tap (CYCLE76)..............................................................................................378
9.2.5
Cirkeltap (CYCLE77)............................................................................................................382
9.2.6
Meerkant (CYCLE79)...........................................................................................................386
9.2.7
Lengtesleuf (SLOT1)............................................................................................................390
9.2.8
Cirkelsleuf (SLOT2)..............................................................................................................397
9.2.9
Open sleuf (CYCLE899)......................................................................................................403
9.2.10
Slobgat (LONGHOLE) - alleen voor G-code programma's..................................................412
9.2.11
Schroefdraadfrezen (CYCLE70)..........................................................................................414
9.2.12
Graveren (CYCLE60)...........................................................................................................417
9.3
Contourfrezen......................................................................................................................423
9.3.1
Algemeen.............................................................................................................................423
9.3.2
Weergave van de contour....................................................................................................423
9.3.3
Nieuwe contour maken........................................................................................................425
9.3.4
Contourelementen maken....................................................................................................427
9.3.5
Contour wijzigen...................................................................................................................432
9.3.6
Contouroproep (CYCLE62) - alleen met G-code programma..............................................433
9.3.7
Baanfrezen (CYCLE72).......................................................................................................434
9.3.8
Contourkamer/contourtap (CYCLE63/64)............................................................................438
9.3.9
Contourkamer voorboren (CYCLE64)..................................................................................440
9.3.10
Contourkamer frezen (CYCLE63)........................................................................................443
9.3.11
Contourkamer restmateriaal (CYCLE63).............................................................................449
9.3.12
Contourtap frezen (CYCLE63).............................................................................................450
9.3.13
Contourtap restmateriaal (CYCLE63)..................................................................................454
9.4
Draaien - Frees-/draaimachine............................................................................................456
9.4.1
Algemeen.............................................................................................................................456
9.4.2
Verspanen (CYLCE951)......................................................................................................456
9.4.3
Groef (CYCLE930)...............................................................................................................460
9.4.4
Ondersnijding vorm E en F (CYCLE940).............................................................................465
9.4.5
Draaduitloop (CYCLE940)...................................................................................................471
9.4.6
Schroefdraad draaien (CYCLE99) - alleen G-code..............................................................477
9.4.7
Schroefdraadkoppeling (CYCLE98).....................................................................................504
9.4.8
Afsteken (CYCLE92)............................................................................................................513
9.5
Contourdraaien - Frees-/draaimachine................................................................................517
9.5.1
Algemeen.............................................................................................................................517
9.5.2
Weergave van de contour....................................................................................................518
9.5.3
Nieuwe contour maken........................................................................................................519
9.5.4
Contourelementen maken....................................................................................................521
9.5.5
Contour wijzigen...................................................................................................................527
Frezen
Bedieningshandboek, 01/2015, 6FC5398-7CP40-5JA2
Inhoudsopgave
15
Advertenties
Inhoudsopgave
