Siemens SINUMERIK 840D sl Bedieningshandboek pagina 12
Draaien
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (329 pagina's)
Advertenties
Inhoudsopgave
8.4.2
Rechthoekige kamer (POCKET3)............................................................................................. 335
8.4.3
Cirkelkamer (POCKET4)........................................................................................................... 339
8.4.4
Rechthoekige tap (CYCLE76)................................................................................................... 344
8.4.5
Cirkeltap (CYCLE77)................................................................................................................. 347
8.4.6
Meerkant (CYCLE79)................................................................................................................ 351
8.4.7
Lengtesleuf (SLOT1)................................................................................................................. 353
8.4.8
Cirkelsleuf (SLOT2)................................................................................................................... 357
8.4.9
Open sleuf (CYCLE899) ........................................................................................................... 361
8.4.10
Slobgat (LONGHOLE) - alleen bij G-code programma............................................................. 368
8.4.11
Schroefdraadfrezen (CYCLE70) ............................................................................................... 370
8.4.12
Graveren (CYCLE60)................................................................................................................ 373
8.5
Contourfrezen ........................................................................................................................... 380
8.5.1
Algemeen .................................................................................................................................. 380
8.5.2
Weergave van de contour ......................................................................................................... 380
8.5.3
Nieuwe contour maken ............................................................................................................. 382
8.5.4
Contourelementen maken......................................................................................................... 384
8.5.5
Contour wijzigen........................................................................................................................ 390
8.5.6
Contouroproep (CYCLE62) - alleen met G-code programma .................................................. 391
8.5.7
Baanfrezen (CYCLE72) ............................................................................................................ 392
8.5.8
Contourkamer/contourtap (CYCLE63/64)................................................................................. 397
8.5.9
Contourkamer voorboren (CYCLE64)....................................................................................... 399
8.5.10
Contourkamer frezen (CYCLE63)............................................................................................. 403
8.5.11
Contourkamer restmateriaal (CYCLE63, optie) ........................................................................ 406
8.5.12
Contourtap frezen (CYCLE63).................................................................................................. 408
8.5.13
Contourtap restmateriaal (CYCLE63, optie) ............................................................................. 410
8.6
Andere cycli en functies ............................................................................................................ 413
8.6.1
Zwenken vlak/gereedschap (CYCLE800)................................................................................. 413
8.6.2
Zwenken gereedschap (CYCLE800) ........................................................................................ 421
8.6.2.1
Uitlijnen van draaigereedschap - alleen bij G-code programma's (CYCLE800)....................... 421
8.6.2.2
Uitlijnen van freesgereedschap - alleen bij G-code programma's (CYCLE800)....................... 423
8.6.2.3
Aanzetten van freesgereedschap - alleen bij G-code programma's (CYCLE800) ................... 424
8.6.3
High Speed Settings (CYCLE832)............................................................................................ 426
8.6.4
Subprogramma's ....................................................................................................................... 428
8.7
Andere cycli en functies ShopTurn ........................................................................................... 430
8.7.1
Boren midden............................................................................................................................ 430
8.7.2
Draad midden............................................................................................................................ 432
8.7.3
Transformaties .......................................................................................................................... 435
8.7.4
Verschuiving.............................................................................................................................. 436
8.7.5
Rotatie ....................................................................................................................................... 437
8.7.6
Schaalverdeling......................................................................................................................... 438
8.7.7
Spiegeling.................................................................................................................................. 439
8.7.8
Rotatie C-as .............................................................................................................................. 440
8.7.9
Rechte en cirkelvormige bewerkingen ...................................................................................... 441
8.7.10
Gereedschap en bewerkingsvlak selecteren ............................................................................ 442
8.7.11
Rechte programmeren .............................................................................................................. 443
8.7.12
Cirkel met bekend middelpunt programmeren.......................................................................... 445
8.7.13
Cirkel met bekende radius programmeren................................................................................ 447
8.7.14
Polaire coördinaten ................................................................................................................... 449
8.7.15
Rechte polair ............................................................................................................................. 451
8.7.16
Cirkel polair ............................................................................................................................... 453
8.7.17
Bewerking met tegenspil ........................................................................................................... 454
8.7.17.1 Programmeervoorbeeld: Bewerking hoofdspil - Overname werkstuk - Bewerking tegenspil... 455
8.7.17.2 Programmeervoorbeeld: Bewerking tegenspil - zonder voorafgaande overname ................... 455
8.7.17.3 Programmeervoorbeeld: Bewerking van baarmateriaal ........................................................... 456
12
Bedieningshandboek, 03/2010, 6FC5398-8CP20-1JA0
Draaien
Advertenties
