Siemens SINUMERIK 840D sl Bedieningshandboek pagina 11
Draaien
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (378 pagina's)
Inhoudsopgave
Advertenties
7.15
Technologische functies oproepen ............................................................................................225
7.15.1
Verdere functies in de invoerschermen .....................................................................................225
7.15.2
Controle van cyclusparameters .................................................................................................225
7.15.3
Instelgegevens voor technologische functies ............................................................................226
7.15.4
Cyclusoproep wijzigen ...............................................................................................................226
7.16
Cyclus voor naderen/verwijderen programmeren......................................................................227
7.17
Meetcyclusondersteuning ..........................................................................................................229
7.18
Voorbeeld: Standaardbewerking................................................................................................231
7.18.1
Werkstuktekening ......................................................................................................................232
7.18.2
Programmering ..........................................................................................................................233
7.18.3
Resultaten/Simulatietest ............................................................................................................246
7.18.4
G-codebewerkingsprogramma...................................................................................................248
8
Technologische functies programmeren (cycli)...................................................................................... 251
8.1
Boren..........................................................................................................................................251
8.1.1
Algemeen ...................................................................................................................................251
8.1.2
Centreren (CYCLE81)................................................................................................................252
8.1.3
Boren (CYCLE82) ......................................................................................................................254
8.1.4
Ruimen (CYCLE85) ...................................................................................................................256
8.1.5
Diepgatboren (CYCLE83) ..........................................................................................................257
8.1.6
Kotteren (CYCLE86) ..................................................................................................................261
8.1.7
Draadtappen (CYCLE84, 840)...................................................................................................263
8.1.8
Draadtapfrezen (CYCLE78).......................................................................................................268
8.1.9
Posities en positiepatroon..........................................................................................................271
8.1.10
Posities naar keuze (CYCLE802) ..............................................................................................272
8.1.11
Positiepatroon Lijn (HOLES1)....................................................................................................274
8.1.12
Positiepatroon Cirkel (HOLES2) ................................................................................................276
8.1.13
Posities herhalen .......................................................................................................................279
8.2
Draaien.......................................................................................................................................280
8.2.1
Algemeen ...................................................................................................................................280
8.2.2
Verspanen (CYLCE951) ............................................................................................................280
8.2.3
Groef (CYCLE930).....................................................................................................................283
8.2.4
Ondersnijding vorm E en F (CYCLE940)...................................................................................286
8.2.5
Draaduitloop (CYCLE940) .........................................................................................................288
8.2.6
Schroefdraad draaien (CYCLE99).............................................................................................291
8.2.7
Schroefdraadkoppeling (CYCLE98) ..........................................................................................300
8.2.8
Afsteken (CYCLE92)..................................................................................................................303
8.3
Contourdraaien ..........................................................................................................................305
8.3.1
Algemeen ...................................................................................................................................305
8.3.2
Weergave van de contour..........................................................................................................306
8.3.3
Nieuwe contour maken ..............................................................................................................307
8.3.4
Contourelementen maken..........................................................................................................309
8.3.5
Contour wijzigen ........................................................................................................................314
8.3.6
Contouroproep (CYCLE62) - alleen met G-code programma ...................................................315
8.3.7
Verspanen (CYLCE952) ............................................................................................................316
8.3.8
Verspanen rest (CYLCE952) .....................................................................................................321
8.3.9
Steken (CYCLE952) ..................................................................................................................323
8.3.10
Steken rest (CYCLE952) ...........................................................................................................325
8.3.11
Steekdraaien (CYCLE952) ........................................................................................................327
8.3.12
Steekdraaien rest (CYCLE952) .................................................................................................330
8.4
Frezen ........................................................................................................................................332
8.4.1
Vlakfrezen (CYCLE61)...............................................................................................................332
Draaien
Bedieningshandboek, 03/2010, 6FC5398-8CP20-1JA0
Inhoudsopgave
11
Advertenties
Inhoudsopgave
