Advertenties
55. Navigation buttons
56. "OK" button
6.3 Cutting height adjustment facility
Important! Adjust the cutting height only when
the robot lawn mower has been switched off . Do
this by pressing the „STOP" button (3). The cutting
height adjustment facility (4) allows the cutting
height of the robot lawn mower to be set to infi ni-
tely adjustable settings between 20 and 60 mm,
which can be viewed on the scale.
If the grass is taller than 60 mm it must fi rst be
shortened to a maximum of 60 mm to avoid expo-
sing the robot lawn mower to excessive load and
adversely aff ecting its operating effi ciency. Use a
conventional lawn mower or trimmer to do this.
After installation has been completed, the cutting
height can be adjusted using the cutting height
adjustment facility (4). Always start with a higher
cutting height and reduce it in small steps until
you reach the desired height.
6.4 Locking mechanism / PIN
The locking mechanism prevents the unautho-
rized use of the robot lawn mower without a valid
code. You have to enter a personal four-digit secu-
rity code for this.
Lock release
Before you start using the robot lawn mower, you
have to enter the correct PIN (standard PIN: "0-0-
0-0"). Enter the PIN with the help of the navigation
buttons (55).
Standard PIN:
New PIN:
0 0 0 0
_ _ _ _
Changing the PIN
To change the PIN, proceed as follows.
1. Unlock the control panel.
2. First press the "SET" button (51) in order to
make your settings.
3. Use the navigation buttons (55) to navigate in
the menu on the LCD (50) to the point "Gene-
ral information" and then "PIN code".
4. First enter the current PIN (standard PIN 0-0-
0-0) with the help of the navigation buttons
(55).
5. Then use the navigation buttons (55) to enter
your personal PIN.
6. Confi rm the settings you have just made.
7. Repeat step 5 and step 6 in order to confi rm
the new PIN.
8. Important! Make a note of the new PIN.
Anl_FREELEXO_CAM_PLUS_SPK13.indb 52
Anl_FREELEXO_CAM_PLUS_SPK13.indb 52
GB
Requesting your PIN if you lose it
Have the receipt and the serial number of the ro-
bot lawn mower ready. You need them in order to
get your PIN.
Version A:
1. Press and hold the "SET" button (51) for 6 se-
conds in locked status.
2. The PUK will now appear in the display (50).
3. Contact the customer services team to obtain
your PIN.
Version B:
1. Connect an empty USB stick to the USB con-
nection (14) as shown (Fig. 11).
2. The robot lawn mower will automatically save
the PUK to your USB stick and will then end
the operation with a beep.
3. Pull out the USB stick. Import the data from
the USB stick to a computer. A text fi le (*.txt)
will have been created by the robot lawn
mower. This fi le contains a PUK (Personal Un-
locking Key). Contact the customer services
team to obtain your PIN.
6.5 Settings of the robot lawn mower
The main menu on the LCD (50) shows you the
current date and time settings of the robot lawn
mower, as well as the current state of the battery
level. At the same time the status of the rain sen-
sor, the wire signal, the selected mode, the GNSS
module and WLAN will appear in the toolbar. On
the control panel you can use either the "SET" but-
ton (51) to make settings on the robot lawn mower
or the "MODE" button (52) to start the robot lawn
mower with various mowing programs. Use the
navigation buttons (55) to go to the option where
you want to make the settings. Press the "BACK"
button (54) in order to exit the respective menu.
6.5.1 Mowing programs – "MODE" button (52)
In the "MODE" menu you can use the navigation
buttons (55) on the one hand to choose between
the two operating modes "Manual" and "Schedule"
and on the other hand to send the lawn mower
back to the charging station.
Manual:
Here you can choose – outside the set schedule
– whether you want to let the robot lawn mower
mow as normal or whether you want it to perform
spot mowing. In each case you can choose bet-
ween main area and secondary area. More details
of the two areas can be found in the section "Be-
fore using for the fi rst time" under "Main area and
- 52 -
04.10.2024 10:05:48
04.10.2024 10:05:48
Advertenties
