Siemens SINUMERIK 840D sl Bedieningshandboek pagina 15
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (718 pagina's)
Inhoudsopgave
Advertenties
8.4.10
Slobgat (LONGHOLE) - alleen bij G-code programma .............................................................428
8.4.11
Schroefdraadfrezen (CYCLE70) ................................................................................................430
8.4.12
Graveren (CYCLE60).................................................................................................................434
8.5
Contourfrezen ............................................................................................................................441
8.5.1
Algemeen ...................................................................................................................................441
8.5.2
Weergave van de contour..........................................................................................................441
8.5.3
Nieuwe contour maken ..............................................................................................................443
8.5.4
Contourelementen maken..........................................................................................................445
8.5.5
Contour wijzigen ........................................................................................................................451
8.5.6
Contouroproep (CYCLE62) - alleen met G-code programma ...................................................452
8.5.7
Baanfrezen (CYCLE72) .............................................................................................................454
8.5.8
Contourkamer/contourtap (CYCLE63/64)..................................................................................459
8.5.9
Contourkamer voorboren (CYCLE64) .......................................................................................461
8.5.10
Contourkamer frezen (CYCLE63)..............................................................................................466
8.5.11
Contourkamer restmateriaal (CYCLE63, optie) .........................................................................469
8.5.12
Contourtap frezen (CYCLE63)...................................................................................................472
8.5.13
Contourtap restmateriaal (CYCLE63, optie) ..............................................................................475
8.6
Andere cycli en functies .............................................................................................................478
8.6.1
Zwenken vlak / Uitlijnen gereedschap (CYCLE800)..................................................................478
8.6.2
Zwenken gereedschap (CYCLE800) .........................................................................................487
8.6.2.1
Uitlijnen van draaigereedschap - alleen bij G-code programma's (CYCLE800)........................487
8.6.2.2
Uitlijnen van freesgereedschap - alleen bij G-code programma's (CYCLE800)........................488
8.6.2.3
Aanzetten van freesgereedschap - alleen bij G-code programma's (CYCLE800) ....................489
8.6.3
High Speed Settings (CYCLE832).............................................................................................491
8.6.4
Subprogramma's........................................................................................................................494
8.7
Andere cycli en functies ShopTurn ............................................................................................496
8.7.1
Boren midden.............................................................................................................................496
8.7.2
Draad midden.............................................................................................................................498
8.7.3
Transformaties ...........................................................................................................................501
8.7.4
Verschuiving...............................................................................................................................503
8.7.5
Rotatie........................................................................................................................................504
8.7.6
Schaalverdeling .........................................................................................................................505
8.7.7
Spiegeling ..................................................................................................................................506
8.7.8
Rotatie C-as ...............................................................................................................................507
8.7.9
Rechte en cirkelvormige bewerkingen.......................................................................................508
8.7.10
Gereedschap en bewerkingsvlak selecteren .............................................................................509
8.7.11
Rechte programmeren ...............................................................................................................510
8.7.12
Cirkel met bekend middelpunt programmeren...........................................................................512
8.7.13
Cirkel met bekende radius programmeren ................................................................................514
8.7.14
Polaire coördinaten ....................................................................................................................516
8.7.15
Rechte polair ..............................................................................................................................518
8.7.16
Cirkel polair ................................................................................................................................520
8.7.17
Bewerking met verplaatsbare tegenspil.....................................................................................522
8.7.17.2 Programmeervoorbeeld: Bewerking tegenspil - zonder voorafgaande overname ....................523
8.7.17.3 Programmeervoorbeeld: Bewerking van baarmateriaal ............................................................524
8.7.18
Bewerking met vaste tegenspil ..................................................................................................529
9
Meerkanalige bewerking (alleen 840D sl) .............................................................................................. 531
9.1
Meerkanalenweergave (alleen 840D sl) ....................................................................................531
9.1.1
Draaien
Bedieningshandboek, 03/2013, 6FC5398-8CP40-3JA1
Inhoudsopgave
15
Advertenties
Inhoudsopgave
