Siemens SINUMERIK 840D sl Bedieningshandboek pagina 14
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (834 pagina's)
Advertenties
Inhoudsopgave
8.1.1
Algemeen .................................................................................................................................. 281
8.1.2
Centreren (CYCLE81)............................................................................................................... 282
8.1.3
Boren (CYCLE82) ..................................................................................................................... 285
8.1.4
Ruimen (CYCLE85) .................................................................................................................. 287
8.1.5
Kotteren (CYCLE86) ................................................................................................................. 289
8.1.6
Diepgatboren (CYCLE83) ......................................................................................................... 293
8.1.7
Draadtappen (CYCLE84, 840).................................................................................................. 297
8.1.8
Draadtapfrezen (CYCLE78) ...................................................................................................... 303
8.1.9
Posities en positiepatroon ......................................................................................................... 307
8.1.9.1
Naderen/verwijderen ................................................................................................................. 307
8.1.10
Posities naar keuze (CYCLE802) ............................................................................................. 308
8.1.10.1 Functie....................................................................................................................................... 308
8.1.11
Positiepatroon lijn (HOLES1), rooster of kader (CYCLE801) ................................................... 311
8.1.12
Positiepatroon Cirkel (HOLES2) ............................................................................................... 314
8.1.13
Posities tonen en verbergen ..................................................................................................... 317
8.1.14
Posities herhalen....................................................................................................................... 319
8.1.14.1 Functie....................................................................................................................................... 319
8.2
Draaien...................................................................................................................................... 320
8.2.1
Algemeen .................................................................................................................................. 320
8.2.2
Verspanen (CYLCE951) ........................................................................................................... 320
8.2.3
Groef (CYCLE930).................................................................................................................... 323
8.2.4
Ondersnijding vorm E en F (CYCLE940).................................................................................. 326
8.2.5
Draaduitloop (CYCLE940) ........................................................................................................ 328
8.2.6
Schroefdraad draaien (CYCLE99) ............................................................................................ 331
8.2.7
Schroefdraadkoppeling (CYCLE98).......................................................................................... 340
8.2.7.1
Parameters................................................................................................................................ 342
8.2.8
Afsteken (CYCLE92)................................................................................................................. 344
8.3
Contourdraaien ......................................................................................................................... 346
8.3.1
Algemeen .................................................................................................................................. 346
8.3.2
Weergave van de contour ......................................................................................................... 347
8.3.3
Nieuwe contour maken ............................................................................................................. 349
8.3.4
Contourelementen maken......................................................................................................... 351
8.3.5
Passingsmaat invoeren............................................................................................................. 356
8.3.6
Contour wijzigen........................................................................................................................ 358
8.3.7
Contouroproep (CYCLE62) - alleen met G-code programma .................................................. 359
8.3.8
Verspanen (CYLCE952) ........................................................................................................... 360
8.3.9
Verspanen rest (CYLCE952) .................................................................................................... 366
8.3.10
Steken (CYCLE952).................................................................................................................. 369
8.3.11
Steken rest (CYCLE952)........................................................................................................... 372
8.3.12
Steekdraaien (CYCLE952)........................................................................................................ 374
8.3.13
Steekdraaien rest (CYCLE952) ................................................................................................ 378
8.4
Frezen ....................................................................................................................................... 381
8.4.1
Vlakfrezen (CYCLE61).............................................................................................................. 381
8.4.2
Rechthoekige kamer (POCKET3)............................................................................................. 385
8.4.3
Cirkelkamer (POCKET4)........................................................................................................... 391
8.4.4
Rechthoekige tap (CYCLE76)................................................................................................... 397
8.4.5
Cirkeltap (CYCLE77)................................................................................................................. 401
8.4.6
Meerkant (CYCLE79)................................................................................................................ 405
8.4.7
Lengtesleuf (SLOT1)................................................................................................................. 408
8.4.8
Cirkelsleuf (SLOT2)................................................................................................................... 414
8.4.9
Open sleuf (CYCLE899) ........................................................................................................... 419
14
Bedieningshandboek, 03/2013, 6FC5398-8CP40-3JA1
Draaien
Advertenties
