Siemens SINUMERIK 840D sl Bedieningshandboek pagina 15
Frezen
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (380 pagina's)
Inhoudsopgave
Advertenties
8.4.5
Draaduitloop (CYCLE940) .........................................................................................................403
8.4.6
Schroefdraad draaien (CYCLE99).............................................................................................406
8.4.7
Schroefdraadkoppeling (CYCLE98) ..........................................................................................415
8.4.8
Afsteken (CYCLE92)..................................................................................................................418
8.5
Contourdraaien - alleen bij G-code programma's......................................................................421
8.5.1
Algemeen ...................................................................................................................................421
8.5.2
Weergave van de contour..........................................................................................................422
8.5.3
Nieuwe contour maken ..............................................................................................................423
8.5.4
Contourelementen maken..........................................................................................................425
8.5.5
Contour wijzigen ........................................................................................................................431
8.5.6
Contouroproep (CYCLE62)........................................................................................................432
8.5.7
Verspanen (CYLCE952) ............................................................................................................433
8.5.8
Verspanen rest (CYLCE952) .....................................................................................................439
8.5.9
Steken (CYCLE952) ..................................................................................................................441
8.5.10
Steken rest (CYCLE952) ...........................................................................................................444
8.5.11
Steekdraaien (CYCLE952) ........................................................................................................446
8.5.12
Steekdraaien rest (CYCLE952) .................................................................................................449
8.6
Andere cycli en functies .............................................................................................................452
8.6.1
Zwenken vlak/gereedschap (CYCLE800)..................................................................................452
8.6.2
Zwenken gereedschap (CYCLE800) .........................................................................................462
8.6.2.1
(CYCLE800)...............................................................................................................................462
8.6.2.2
Zwenken uitlijnen gereedschap - alleen bij G-codeprogramma's (CYCLE800) ........................464
8.6.3
High Speed Settings (CYCLE832).............................................................................................465
8.6.4
Subprogramma's........................................................................................................................468
8.7
Andere cycli en functies ShopMill ..............................................................................................470
8.7.1
Transformaties ...........................................................................................................................470
8.7.2
Verschuiving...............................................................................................................................471
8.7.3
Rotatie........................................................................................................................................472
8.7.4
Schaalverdeling .........................................................................................................................473
8.7.5
Spiegeling ..................................................................................................................................474
8.7.6
Cilindermanteltransformatie .......................................................................................................475
8.7.6.1
Algemene programmering .........................................................................................................477
8.7.7
Rechte of cirkelvormige baanbewerkingen................................................................................478
8.7.8
Rechte programmeren ...............................................................................................................480
8.7.9
Cirkel met bekend middelpunt programmeren...........................................................................481
8.7.10
Cirkel met bekende radius programmeren ................................................................................482
8.7.11
Helix ...........................................................................................................................................483
8.7.12
Polaire coördinaten ....................................................................................................................484
8.7.13
Rechte polair ..............................................................................................................................485
8.7.14
Cirkel polair ................................................................................................................................486
8.7.15
Hindernis ....................................................................................................................................487
9
Meerkanalenaanzicht............................................................................................................................. 489
9.1
Meerkanalenaanzicht.................................................................................................................489
9.2
9.3
Meerkanalenweergave bij grote bedieningspanelen .................................................................492
9.4
Meerkanalenaanzicht instellen...................................................................................................494
Frezen
Bedieningshandboek, 02/2012, 6FC5398-7CP40-3JA0
Inhoudsopgave
15
Advertenties
Inhoudsopgave
