Inhoudsopgave
Advertenties
NOTE
The battery must be charged and connected in order to
start the product. To do so, check the charge status of
the battery on the battery display (green: adequately
charged, black: must be charged, white: replace the
battery).
Do not connect any consumers before starting the gener-
ator.
Allow the power generator to run for a short time (approx.
30 seconds) without load before switching it off so that it
can "cool down". To do so, switch off the connected con-
sumers.
1. Use the locking mechanism (6) to open the mainte-
nance door (5).
2. Check that the mechanical ON/OFF switch (31) is en-
gaged in the correct position (RUN).
Important! The mechanical ON/OFF switch (31) is
set at the factory and may not be changed.
3. Close the maintenance door (5).
4. Switch on the 230 V circuit breaker (23) or the 400 V
circuit breaker (16) (ON position).
5. Insert the ignition key (A) into the ignition (11).
6. Pull the choke (13) when starting a cold engine. If you
start the engine when it is warm, then the choke (13)
is not needed.
7. Turn the ignition key (A) to the "ON" position
NOTE
If the engine is being started for the first time, several
tries are required to start until the fuel has been deliv-
ered from the tank to the engine.
8. Set the voltage selector switch (15) to the desired po-
sition (i.e. 230 V or 400 V).
9. Now connect the corresponding consumer.
NOTE
If the product's battery is empty, the engine cannot be
started.
To avoid discharging the battery, it is recommended to
operate the power generator for at least 30 minutes
once a month. If the power generator is not used for a
longer period of time, disconnect the battery from the
terminals.
NOTE
With high outside temperatures, it may be necessary to
start the power generator without the choke even when
the engine is cold!
30 | GB
NOTE
400 V heavy current:
The load of a three-phase power generator must be dis-
tributed over all three phases, balancing the load for all
phases.
The load per phase must not exceed 1/3 of the total
generator power. The permissible imbalance shall not
exceed 20%. Loading only the 1st or 2nd phase will re-
sult in a device failure. The total load and current for all
three phases must not exceed the normal load and cur-
rent of the power generator.
9.3
Switch off the engine (Fig. 1, 3)
Allow the power generator to run for a short time (approx.
30 seconds) without load before switching it off so that it
can "cool down". To do so, switch off the connected con-
sumers.
1. Turn the ignition key (A) to the "OFF" position.
2. Set the voltage selector switch (15) to the "OFF" posi-
tion.
3. Disconnect the power consumers from the product.
ATTENTION
–
Do not switch off the diesel power generator when
the connected loads are in operation.
–
Use the mechanical ON/OFF switch only in an
emergency.
9.4
Voltage indicator (14) (Fig. 3)
The voltage indicator (14) is active when the engine is
running and shows the output voltage.
9.5
Overload protection - circuit
breaker 400 V (16) and circuit
breaker 230 V (23) (Fig. 3)
The overload protection becomes active if the power con-
sumption is too high and switches off the 230 V or 400 V
socket. The circuit breakers 400 V (16) or 230 V (23) are
automatically set to the "OFF" position.
1. Switch off the product, as described under 9.3.
2. Disconnect the power consumers from the product.
3. Wait a minute.
4. Set the 400 V circuit breaker (16) or the 230 V circuit
breaker (23) to "ON".
ATTENTION
Defective circuit breakers may only be replaced with
identical circuit breakers with the same power data.
Contact customer service for this.
9.6
"RESET" button (21) for 12 V (Fig. 3)
If the overload protection has been triggered, the "RE-
SET" button (21) restores the output power of the diesel
power generator. It is then not necessary to restart the
engine.
1. Wait a minute.
2. Press the "RESET" button (21).
www.scheppach.com
Advertenties
Hoofdstukken
Inhoudsopgave
