Download Inhoudsopgave Inhoud Print deze pagina

Bleeding The Differential Pressure Sensor; Running-In Time Of The Floating Ring Seal; Operating Control - Biral VivarA Originele Montage- En Bedrijfshandleiding

Inline
Inhoudsopgave

Advertenties

72 | English
7.2.2 Closed or open systems where the liquid level is below the inlet of the pump.
1.2
OPEN
3
"X"
IL00004761_00
7.3

Bleeding the differential pressure sensor

The differential pressure sensor must be bled after installation.
Werkstoff:
Warning
VivarA-S 65-340_A71
Auffüllen und Entlüften
Pay particular attention to your own safety when dealing with hot media to avoid
burns.
7.4

Running-in time of the floating ring seal

The sealing surfaces of the floating ring seal are lubricated by the pumped medium, so that a cer-
tain leakage flow is always to be expected which exits the floating ring seal.
After commissioning the pump for the first time or when a new floating ring seal has been installed,
a certain running-in period is required before the leakage rate drops to an acceptable level. The
required running-in period depends on the operating conditions. This means that every time the
operating conditions change, a new running-in period begins.
Under normal operating conditions, the leakage fluid evaporates. Therefore, the leakage is not
Datum
Visum
visible.
7.5

Operating control

After switching on the supply voltage, the pump must start automatically: The Biral impeller rotates
Biral AG
CH-3110 Münsingen
and lights up green.
Pumpe läuft normal
The pump runs according to the basic settings (see Section 9.)
Pumpe Extern OFF
2
1.1
LV
Biral AG
CH-3110 Münsingen
Ersetzt durch:
Massstab
1:2
Zeichnungsnummer
961704
1. Close the isolation valve on the pressure
CLOSE
side of the pump and open the isolation
valve on the suction side completely.
2. Loosen the bleeding screw (LV) on the
pump. (See Section 2.4 "Connections")
3. Fill in the medium through a filler opening
"X" until the suction line and the pump are
completely filled.
4. Screw the bleeding screw (LV) back in and
tighten it.
Dokumentstatus:
Massstab
1:1
1:1
in Arbeit DS
Format:
A3
Erstelldatum
12.10.2020
PDM_Nr:
207543
Änd. Ind.
Zeichnungsnummer
IL00004761
00
Rev.
Prior to this, the pump must be installed and
the system filled. The system pressure must be
applied. Then proceed as follows:
1. Loosen the union piece of the capillary
tubes from the suction and pressure con-
nection, but do not remove it completely.
2. Wait until the medium flows out continuous-
ly.
3. Retighten the union piece manually.
Ersatz für:
gezeichnet 10.03.2014
ts
geprüft
13.05.2014
ts
Freigabe
13.05.2014
ts
PDM_Nr
TD-0025856
Änd.Index
00
Drehung drehend
Muster normal
Farbe grün
Drehung stehend
Muster blitzend
sta
A
Vers.
Pumpe steht. Störung (Problemfälle)
Pumpe steht. Störung (Problemfälle)
Pumpe läuft. Störung (Problemfälle)
Drehung
Muster bl
Farbe rot
Drehung
Muster no

Advertenties

Hoofdstukken

Inhoudsopgave
loading

Deze handleiding is ook geschikt voor:

Vivara sVivara m

Inhoudsopgave