Inhoudsopgave
Advertenties
Parts and Functions
Indoor Unit
8
1.Inlet
2.Air Purifying Filter(inside)
3.Display board
EN
4.Emergency Switch
5.Outlet
Display board
1.Signal receiver
2.Temp.display
3.Wi-Fi
4.Operation mode indicator
(lights up when the compressor is on.)
Actual inlet grille may vary from the one shown in the manual
according to the product purchased
Outdoor Unit
OUTLET
1.
2.
INLET
3.
CONNECTING PIPING AND ELECTRICAL WIRING
4.
DRAIN HOSE
Please be subject to the actual produce purchased the above
picture is just from your reference.
3
1
2
7
6
5
6.Vertical blade (adjust left and
right air flow)
7.Horizontal flap (adjust up and
down air flow. Don't adjust it
manually)
8.Inlet grille
1
2
1
2
Remote controller
1
2
3
3
4
4
5
9
10
11
12
13
14
15
16
17
1.Mode display
Operation mode
AUTO COOL
3
Remote
controller
2.Signal sending display
3
3.SWING display
4
4.FAN SPEED display
LO
MED
HI
5.LOCK display
6.TIMER OFF display
TIMER ON display
7.TEMP display
8.Additional functions
display
Loading of the battery
Note
The distance between the signal transmission head and the
●
receiver hole should be within 7m without any obstacle as well.
4
When electronic-started type fluorescent lamp or change- over
●
type fluorescent lamp or wireless telephone is installed in the room,
the receiver can to be disturbed in receiving the signals,so, the
distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
●
batteries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
●
remove the batteries and reload several minutes later.
Hint：Remove the batteries in case won't be in use for a long
period. If there is any display after taking-out, just press reset
key.
6
Operation mode
QUIET
SLEEP
Remote
7
controller
9. TURBO/QUIET button
10. MODE button
11. I FEEL button
8
12. SWING left/right button
13. FAN SPEED button
18
14. HEALTH button
19
15. TIMER button
20
16. WIFI button
17. LIGHT button
21
Control the lightening and
extinguishing of the indoor LED
22
display board.
23
18. POWER ON/OFF button
24
19. ECO button
25
20. TEMP button
21. SWING up/down button
26
22. SLEEP button
23. EXTRA FUNCTION button
Function: A-B yard---> Healthy airflow
position1--->Healthy airflow position
DRY
FAN
HEAT
2 --->10°C heating (If there is not the
10°C button) --->ºF/ºC transform
24.CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions
Display
25. RESET button
circulated
AUTO
When the remote controller appears
abnormal, press this button 3s to
reset the remote.
26. 10 °C button (special heating
set function: 10 degree heating
maintaining) or SELF CLEAN button
1.Remove the battery cover
2.Load the batteries as illustrated. 2 R-03
batteries, resetting key(cylinder); Be sure
that the loading is in line with the " + "/"-"
3.Load the battery, then put on the cover
back again.
ECO
TURBO
HEALTH
Advertenties
Hoofdstukken
Inhoudsopgave
Probleemoplossen
Gerelateerde Producten voor Hansgrohe AS25PCHHRA-NR
- Hansgrohe Raindance Classic AIR 27424 Series
- Hansgrohe Raindance Classic AIR 27428 Series
- Hansgrohe Raindance Classic AIR 27430 Series
- Hansgrohe Raindance Classic AIR 27400 Series
- Hansgrohe Raindance Classic AIR 27406 Series
- Hansgrohe AXOR 42604 Series
- Hansgrohe AXOR 42605 Series
- Hansgrohe AXOR 42610 Series