Inhoudsopgave
Advertenties
Operation
I FEEL Operation
Press
button
1. Only for COOLING, HEATING or AUTO mode(other modes
cannot be implemented).
2. Place the remote controller within the acceptable range of air
conditioner. Press the
the "
" icon. The remote controller sends the circulation
temperature date to the indoor unit every 3 minutes, and the air
conditioner runs according to this data.
EN
3. Exit "I FEEL " mode when power off , press the
or switch other modes.
NOTE:
Please put the remote controller near user when this function
is set. Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate ambient temperature.When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
SELF-CLEAN Operation
（only applicable to mono models）
■ Functional description:
the purpose of this function is to clean the evaporator.
■ Entry and exit：
When the SELF CLEAN function is required, you have two ways to
achieve it.
If you have a
button , press this button to enter this
function, then the display will show "CL" on the panel of the indoor
unit and on the remote controller.
If you do not have a
Maximum running time in this function is no more than 21 minutes.
This function will exit automatically with the " Pi " sound twice, then
the unit return to original state. During SELF CLEAN operation,
pressing the button repeatedly will not exit the process. Press ON/
OFF button to exit this mode.
NOTE:
1.This function is invalid in TIMER / SLEEP mode.
2.After this mode starts, the air volume may reduce, have no
airflow, or even cold airflow blowing.
7
button,the remote control displays
button ,please access in the hOn APP.
3.It is normal if the unit makes some sound when the air expands
with heat and contracts with cold.
4.The "CL" display time may last differently on the remote controller
and panel.
5.If the outside ambient temperature is below zero, error code "F25
"may be show up during self-cleaning operation, which is normal
protection, please turn off the power and restart after 10 seconds.
6.The best condition to run this mode is temperature is between
20ºC~27ºC , the humidity is between 35%~60% indoors, and the
temperature is between 25ºC~38ºC (cooling season)outdoors.
7.It is hard for the air to frost if the air is too dry (humidity<20%).
The condensate water may increase if the humidity of the air is too
button
high (humidity>70%) .
Steri Clean Operation
When the 56ºC Steri-clean function is required, please access in
the hOn APP.
Introduction to Steri Clean
Stage 1 - Self Clean: to remove dirt away. This function freezes
the evaporator with moisture in the air, and removes dirt during the
melting process.The hydrophilic aluminium coating with smaller
angel (ɑ≈5°)helps increase water drainage efÏciency.
Stage 2 - 56ºC high temperature sterilisation: It utilizes smart
temperature monitoring and frequency control technology to adjust
the compressor operation, so that we maintain the evaporator
temperature at high temperature for over 30mins to kill any
bacteria and virus inside the air conditioner.
Stage 3 - Rapid evaporator cooling to enhance the sterilisation
performance. The foil surface is coated with silver nano-particles
which has an anti-bacterial efÏciency up to 99%.
Attention:
1.The function lasts 60-80 minutes.
2.Hot air may come out during the process when evaporator is
heated to 56ºC or maintains at 56ºC in summer.
3.This function may cause changes in room air temperature in
winter.
4.When outdoor ambient temperature is above 36ºC, the function
cannot be performed. Instead, Self Clean function will be turned on
and lasts 21mins when Steri Clean is turned on.
（only applicable to mono models）
Advertenties
Hoofdstukken
Inhoudsopgave
Probleemoplossen
Gerelateerde Producten voor Hansgrohe AS25PCHHRA-NR
- Hansgrohe Raindance Classic AIR 27424 Series
- Hansgrohe Raindance Classic AIR 27428 Series
- Hansgrohe Raindance Classic AIR 27430 Series
- Hansgrohe Raindance Classic AIR 27400 Series
- Hansgrohe Raindance Classic AIR 27406 Series
- Hansgrohe AXOR 42604 Series
- Hansgrohe AXOR 42605 Series
- Hansgrohe AXOR 42610 Series