Inhoudsopgave
Advertenties
Par. Naam
Omschakelbare par.
parameterset 1
5__
MONITORING FUNCTIONS
50_
Speed monitoring
500
Speed monitoring 1
501
Deceleration time 1
504
Encoder monitoring
52_
Mains OFF monitoring
Mains OFF response
520
time
521
Mains OFF response
53_
Motor temperature protection
530
Sensor type 1
531
Sensor type 2
6__
TERMINAL ASSIGNMENT
60_
Binary inputs basic unit
–
Binary input DIØØ
600
Binary input DIØ1
601
Binary input DIØ2
602
Binary input DIØ3
603
Binary input DIØ4
604
Binary input DIØ5
62_
Binary outputs basic unit
–
Binary output DBØØ
620
Binary output DOØ1
621
Binary output DOØ2
64_
Analog output
640
Analog output AO1
641
Scaling AO1
642
Operating mode AO1
7__
CONTROL FUNCTIONS
70_
Operating modes
700
Operating mode 1
71_
Standstill current
710
Standstill current 1
72_
Setpoint stop function
720
Setpoint stop function 1 ON / OFF
721
Stop setpoint 1
722
Start offset 1
Technische handleiding – MOVIDRIVE
Instelbereik
Na inbe-
Fabrieksinstelling
drijfstelling
OFF / MOTOR /
REGENERATIVE /
MOT®EN.MODE
0...1...10 s
ON / OFF
0...5 s
CONTROL.INHIBIT
EMERGENCY STOP
No sensor / TF-TH
No sensor / TF-TH
Vaste toewijzing van: /
CONTROLLER INHIBIT
CW/STOP
CCW/STOP
ENABLE/STOP
n11/n21
n12/n22
Vaste toewijzing van: /BRAKE
READY FOR
OPERATION
NO FUNCTION
ACTUAL SPEED
–10...0...1...10
OFF / 0...20 mA / 4...20
mA
VFC 1
VFC 1 & GROUP
VFC 1 & HOIST
VFC 1 & DC BRAK.
VFC 1 & FLYSTART
VFC-n-CONTROL
VFC-n-CTRL&GRP.
VFC-n-CTRL&HOIST
VFC-n-CTRL&IPOS
CFC
CFC & M-CONTROL
CFC&IPOS
SERVO
SERVO&M-CONTROL
SERVO&IPOS
0...50% I
mot
0...30...500 1/min
0...30...500 1/min
®
compact MCH4_A
Inbedrijfstelling
Complete parameterlijst
Par. Naam
parameterset 2
502 Speed monitoring 2
503 Deceleration time 2
De volgende functies kunnen worden geprogrammeerd: NO
FUNCTION • ENABLE/RAP.STOP • CW/STOP • CCW/STOP •
n11(n13) • n21(n23) • n12(n13) • n22(n23) • FIX SETPT SW.OV. •
PAR. SWITCHOVER• RAMP SWITCHOVER • MOTOR POT UP •
MOT POT DOWN • /EXT. FAULT • FAULT RESET • /HOLD
CONTROL • /LIM. SWITCH CW • /LIM. SWITCH CCW • IPOS
INPUT • REFERENCE CAM • REF.TRAVEL START • SLAVE FREE
RUNN. • SETPOINT HOLD • MAINS ON • DRS SET ZERO
De volgende meldingen kunnen worden geprogrammeerd: NO
FUNCTION • /FAULT • READY • OUTP.STAGE ON • ROT. FIELD
ON • BRAKE RELEASED • BRAKE APPLIED • MOTOR
STANDSTILL • PARAMETER SET • SPEED REFERENCE • SPEED
WINDOW • SP/ACT.VAL.COMP. • CURR. REFERENCE • Imax-
SIGNAL • /MOTOR UTILIZ. 1 • /MOTOR UTILIZ. 2 • IPOS IN
POSITION • IPOS REFERENCE • IPOS OUTPUT • /IPOS FAULT
De volgende functies kunnen worden geprogrammeerd: NO
FUNCTION • RAMP INPUT • SPEED SETPOINT • ACTUAL SPEED
• ACTUAL FREQUENCY • OUTPUT CURRENT • ACTIVE
CURRENT • UNIT UTILIZATION • IPOS OUTPUT • RELATIVE
TORQUE
701 Operating mode 2
711 Standstill current 2
723 Setpoint stop function 2 ON / OFF
724 Stop setpoint 2
725 Start offset 2
I
0 0
Instelbereik
Na inbe-
Fabrieksinstelling
drijfstelling
OFF / MOTOR /
REGENERATIVE / MOT
®EN.MODE
0...1...10 s
VFC 2
VFC 2 & GROUP
VFC 2 & HOIST
VFC 2 & DC BRAK.
VFC 2 & FLYSTART
0...50% I
mot
0...30...500 1/min
0...30...500 1/min
5
75
Advertenties
Inhoudsopgave
