Download Inhoudsopgave Inhoud Print deze pagina

human care FloorLine-i Plus Gebruikshandleiding pagina 28

Inhoudsopgave

Advertenties

Beschikbare talen

Beschikbare talen

9. Operation Instructions
2. Also on the bed base, use the 5mm Allen Key
to loosen ONLY, the 4 Centre Saddle Locking
Bolts (locking bolts sit outside of the hinging
circlip pins). DO NOT REMOVE THE LOCKING
BOLTS, from the lower beam centre saddle.
Remove mattress platform
1. At each pedestal end, use the 5mm Allen Key,
to completely loosen all 4 Mattress Platform
Upper Beam Fixing-Bolts that are seated
in the Fixed (foot end) and Swinging (head
end) Pedestal End Bracket J-Hooks. DO NOT
REMOVE THE NUTS from the end of these
Fixing-Bolts.
2. Using handset, take bed to its lowest position.
3. Unplug the Mains Power Cable from the
power outlet and safely store it, out of the
way.
The 4 Fixing-Bolts must be un-slotted from the
J-Hooks (one on each side, and at each end).
4. Standing either side of the head end, lift out
the beams. The Swinging J-Hook may facilitate
disconnection. Lay carefully on bed base, so
as not to scratch bed paintwork.
5. Repeat the above step at the foot end.
6. With one person on either side, carefully
lift the platform up and off the bed base.
Carefully place on the protected floor, on
its side edge. Take care not to scratch bed
paintwork.
Keep all cables and actuators safe!
Fold mattress platform
1. Holding the mattress platform upright, tape
the backrest and kneebreak panels to the
mattress platform frame. This prevents them
from swinging loose and getting damaged.
2. Remove the 2 locking lanyard pins on either
side of the centre hinge saddle.
3. Fold the two ends together and secure closed
by reinserting the lanyard pins in the same
holes and hooking the metal transport latch.
4. Store safely.
Fold bed base
28
1. All bolts have been pre-loosened, as above.
2. Ensure the J-Hooks are put back into their
original positions, on each pedestal end.
Failure to do this may damage bed!
3. Remove the 4 Lower Beam Centre Saddle
Locking Bolts (Locking Bolts are on the outside
of the Hinging Circlip Pins).
4. On either side of the Head End, hold the
pedestal end cap at the top of the pedestal
with one hand, and with the other hand reach
down and firmly lift the Head End Cross Bar,
that joins the two lower beams, to lift the
slots on the Lower Beam Brackets off the
Pedestal Bracket Latch Bolts. Slowly fold the
Head End pedestal down flat onto the bed
base beams.
5. Lock head end pedestal to the beams with the
plastic transport latch.
6. Repeat the above for the foot end pedestal.
7. Unlock the Foot End Castors ONLY.
8. Standing either side of the centre hinging
saddle, pull the saddle cross bar up, folding
the beams/pedestal ends into a vertical
position. The base will roll along the foot end
castors into a folded position standing on its
4 castors.
9. Ensure that the centre saddle is horizontal
to replace the 4 Centre Saddle Locking Bolts,
with the 5mm Allen Key, thus locking the base
into its folded position.
10. Safely lock all castors, until ready to move
the bed.
9.13 CPR Emergency quick release system
(this information is only for the FloorLine-i
Plus bed)
The CPR emergency procedure (combined
rescue breathing and chest compressions) is
used on a patient in cardiac arrest. CPR can be
administered when the bed is in a CPR position -
a totally horizontally, flat mattress platform.
The FloorLine-i Plus bed is fitted with CPR Quick
Release Levers, and also a CPR button on the
Attendant Control Keypad.
ENG
www.humancaregroup.com

Advertenties

Inhoudsopgave
loading

Deze handleiding is ook geschikt voor:

Floorline-i90500905049030090303

Inhoudsopgave