Inhoudsopgave
Advertenties
EN
Connect the plug of the USB cable to the input socket of the USB Type C product, then connect the USB cable to the charger.
Connect the charger to a mains socket. A red light will illuminate while the product is charging. The product will be fully charged
when the light is green and the charge indicator on the product display shows 100%. Immediately after charging is complete,
disconnect the charger from the mains socket and then unplug the USB cable from the product socket.
Charging from the car battery
ATTENTION! It is forbidden to connect starting terminals of the device to each other. A short circuit can cause burns, electric
shock, fi re and even explosion!
ATTENTION! Do not leave the device unattended while charging.
ATTENTION! Do not use the charging socket for mobile devices when charging the product.
The product can be recharged using the remaining energy in the vehicle's battery. To charge the unit from the car battery connect
the terminals of the starter cables to the battery terminals. Pay attention to the correct polarity. The terminal marked as "+" must
be connected to the battery terminal with the same symbol. The terminal marked as "-" must be connected to the battery terminal
with the same symbol. Press the switch briefl y. A red light will illuminate while the product is charging. The product will be fully
charged when the light is green and the charge indicator on the product display shows 100%. Disconnect the terminals of the
starter cables from the battery terminals immediately. Disconnect terminals one at a time. First disconnect the terminal marked '-',
then disconnect the terminal marked '+'. Place the clamps in the holders located on the product housing.
CAUTION! If, when connected to the battery, the product does not charge or the charge is not full, this may indicate that the battery
is over-discharged. The voltage at the battery terminals must be within the range shown in the technical data table.
Switching the device on and off
The device is switched on by briefl y pressing the switch. When the product is powered up, it will carry out a device check. When
the green light comes on, it indicates that the product is ready for use. The product switches off automatically after detecting
inactivity for approximately 30 seconds.
Changing the language of messages
It is possible to change the language of the messages displayed on the product display from Polish to English or from English to
Polish. Make sure that the device is switched off and not connected to the charger. With the device turned on, use a paper clip to
press the "RESET" button. The device will turn off , then press the power button and after the device turns on, press and hold the
power button until the menu language changes.
Use of the product for starting a vehicle equipped with a battery
ATTENTION! It is forbidden to connect starting terminals of the device to each other. A short circuit can cause burns, electric
shock, fi re and even explosion!
Switch on the device by pressing the switch briefl y. When the product is powered up, it will carry out a device check. When the
green light comes on, it indicates that the product is ready for use.
Connect the terminals of the jump leads to the battery terminals. Pay attention to the correct polarity. The terminal marked as "+"
must be connected to the battery terminal with the same symbol. The terminal marked as "-" must be connected to the battery
terminal with the same symbol. Once the starter cables are connected, if the product needs to be charged, the device will start
charging from the battery. A red light will illuminate while the product is charging. The product will be fully charged when the
green indicator light comes on and the charge indicator on the product display shows 100%, the voltage value rises to approx.
15 V. Then press the switch briefl y. The unit will start a countdown to vehicle start 6 – 0, followed by a capacitor discharge time of
approximately 10 seconds. During this time the device will emit an intermittent beep, start the vehicle. If the vehicle does not start
within this time, repeat the start-up procedure from the beginning. After successfully starting the vehicle, wait until the device is au-
tomatically fully charged. Once the charging process is complete, immediately disconnect the terminals of the starter cables from
the battery terminals. Disconnect terminals one at a time. First disconnect the terminal marked '-', then disconnect the terminal
marked '+'. Place the clamps in the holders located on the product housing. Leaving the product idle for approximately 30 seconds
will cause it to switch off automatically. Once the jump starting is complete, proceed with product maintenance.
Use of the product for starting a vehicle without a battery
ATTENTION! It is forbidden to connect starting terminals of the device to each other. A short circuit can cause burns, electric
shock, fi re and even explosion!
ATTENTION! It is forbidden to use the device for starting if the voltage indicator on the device display indicates less than 12 V.
Prepare the product by charging it fully.
Warning! Pressing and holding the switch for approx. 5 seconds will activate the forced-output mode which will deactivate the
spark protection, short-circuit protection and misconnection protection for the terminals of the starter cables. When using this
operating mode, exercise extra care to prevent any shorting between the terminals of the device.
O R I G I N A L
I N S T R U C T I O N S
11
Advertenties
Inhoudsopgave
