Inhoudsopgave
Advertenties
Translation of the original instructions
MADE IN FRANCE
OPTICAL RADIATIONS
• Risk of optical emission when heated metal elements approach and approach and reach fusion.
• Optical radiation can be harmful to the eyes and skin.
ELECTRICAL RISK
An electric shock could cause serious injuries or potentially even deadly accidents.
110LG / 160LG / 220LG
110LG / 160LG
• The maximum absorbed current (I1) is indicated on the equipment for the maximum operating conditions. Check that the power supply and its
protection (fuse and/or circuit breaker) are compatible with the current needed by the machine.
• The maximum absorbed current (I1) is indicated on the equipment for the maximum operating conditions.
• Do not use the appliance if the power cable, the mains plug or the lance are damaged.
• Do not use the inductor in the rain or on wet or submerged parts.»
EMC CLASSIFICATION
110LG / 160LG
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualified person. A yearly maintenance is recommended.
• Warning ! Always disconnect from the mains before performing maintenance on the device. High Voltage and currents inside
the machine.
• Remove the casing on a regular basis, to remove any excess dust. Take this opportunity to have the electrical connections
checked by a qualified person, using an insulated tool.
• Do not use solvents or any agressive cleaning products.
• Clean the device's surfaces with a dry cloth.
• If the power cable or connection cables are damaged, they must be replaced by the manufacturer, its after sales service or an equally qualified
person to prevent danger.
• If the internal fuse is melted, it must be replaced by the manufacturer, its after-sales service or by an equally qualified person to prevent any
accidents.»
• Do not obstruct the machine's air intake, which facilitates air circulation. Check the installation chapter before using the device.
• Maintain at least 50 cm of free space around the equipment.
TRANSPORT
• Do not use the power cable or nozzle to move the unit. It must be moved in a vertical position.
• The handle cannot be used to lift the product.
REGULATIONS
• The device complies with the European directives,
• The declaration of conformity is available on our website (see cover page).
• EAC conformity mark (Eurasian Economic Commission)
• Material conforms to UK requirements.
• The UK Declaration of Conformity is available on our website (see cover page).
• Device compliant with Moroccan standards.
• The C( مCMIM) declaration of conformity is available on our website.
24
POWERDUCTION 110LG / 160LG / 220LG
• The appliance is class I and should only be used on a 3-phase 400V (50/60 Hz) four-wire electrical
400 V
installation with a neutral conductor connected to earth.
• The appliance is class I and should only be used on a 3-phase 208-240V (50/60 Hz) four-wire electrical
UL Standard
installation with a neutral conductor connected to earth.
• These Class A devices are not intended to be used on a residential site where the electric current is supplied
by the public network, with a low voltage power supply. There may be potential difficulties in ensuring
electromagnetic compatibility at these sites, due to conducted interferences as well as radiation.
• This equipment complies with IEC 61000-3-12, provided that the power of the short-circuit Ssc is equal to or
greater than 7.6 MVA at the interface between the machine and the mains power network.
220LG
• It is the responsibility of the installer or user of the equipment to ensure if necessary by consulting the operator
only
of the mains electricity, that the equipment is only connected to a power supply where the power of short-
circuit ssc is equal to or greater than 2.8MVA.
• This equipment does not comply with IEC 61000-3-12 and is intended to be connected to domestic low-voltage
systems interfacing with the public supply only at the medium- or high-voltage level. If connected to a public
low-voltage power grid, the installer or user of the machine has to ensure, by checking with the network
operator, that the device can be connected.
• This equipment complies with the IEC 61000-3-11 standard.
EN
Advertenties
Inhoudsopgave
