Advertenties
Beschikbare talen
Beschikbare talen
3. Add the full quantity of the two-cycle engine oil to the
fuel container.
CAUTION: Always use air-cooled two-
cycled engine oil of high quality. Other
oils can cause damage to the product.
4. Shake the fuel mixture to mix the contents.
5. Add the remaining gasoline quantity to the fuel
container.
6. Shake the fuel mixture to mix the contents.
7. Fill the fuel tank of the product with the fuel mixture.
To use fuel on page 16 .
See
To fill the fuel tank
1. Make sure that the fuel mixture is correct and that
the fuel mixture is in a fuel container with an antispill
valve.
2. If fuel is on the container, remove the unwanted fuel
and let the container dry.
3. Make sure that the area near the fuel tank cap is
clean.
4. Remove the fuel tank cap.
5. Shake the fuel container before you add the fuel
mixture to the fuel tank.
6. Put back the fuel tank cap.
To lubricate the saw chain
The product has an automatic lubrication system. The
saw chain oil tank and the fuel tank are designed so that
the fuel runs out before the saw chain oil. This safety
feature requires that the correct chain oil is used and
that the instructions are obeyed.
1. Use vegetable-based saw chain oil or a standard
chain oil.
2. Make sure that the area near the cap of the saw
chain oil tank is clean.
3. Remove the cap of the saw chain oil tank.
4. Fill the saw chain oil tank with the recommended
saw chain oil.
5. Put back the cap of the saw chain oil tank.
To start and stop
Before you start the engine
•
Examine the product for missing, damaged, loose or
worn parts.
•
Examine the nuts, screws and bolts.
•
Examine the air filter.
•
Examine the trigger lockout and the trigger for
correct operation.
•
Examine the stop switch for correct operation.
•
Examine the product for fuel leaks.
•
Examine the saw chain sharpness and tension.
658 - 002 - 11.04.2018
To start a cold engine
1. Move the front hand guard forward to engage the
chain brake. (Fig. 47 )
2. Push the primer bulb 6 times. (Fig. 48 )
3. Move the choke control to the full choke position.
(Fig. 49 )
4. Hold the body of the product on the ground with your
left hand. Put your right foot in the rear handle to
make the chainsaw stable. Pull the starter rope
handle slowly until you feel some resistance. Then
pull the starter rope handle with force 5 times. (Fig.
50 )
Note: Do not pull the trigger while you start the
engine.
5. Move the choke control to the no choke position.
6. Pull the starter rope handle until the engine starts.
Wait 60 seconds after a start before you pull the
trigger.
CAUTION: Do not pull the starter rope
until it stops. Do not let go of the starter
rope when it is fully extended. Release
the starter rope slowly. Obey these
instructions to prevent damage to the
engine.
7. Pull the front hand guard in the direction of the front
handle to disengage the chain brake.
8. Hold the rear handle with your right hand and the
front handle with your left hand.
9. Use the product.
To start a warm engine
1. Move the front hand guard forward to engage the
chain brake.
2. Push the primer bulb 6 times.
3. Move the choke control to the full choke position.
4. Move the choke control to the no choke position.
5. Hold the body of the product on the ground with your
left hand. Put your right foot in the rear handle to
make the chainsaw stable.. Pull the starter rope
handle slowly until you feel some resistance. Then
pull the starter rope handle with force until the
engine starts. (Fig. 51 )
Note: Do not pull the trigger while you start the
engine.
CAUTION: Do not pull the starter rope
until it stops. Do not let go of the starter
rope when it is fully extended. Release
the starter rope slowly. Obey these
instructions to prevent damage to the
engine.
17
Advertenties
