Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
9. Workpiece supports (21) must always be secured
and used during work.
Set the desired projection by loosening the locking
screw (20). Then retighten the locking screw (20).
10.2 Dust bag (30) (Fig. 1, 24)
The saw is equipped with a dust bag (30) for chips.
Squeeze the wings of the metal ring on the dust bag (30)
together and slide it over the discharge port near the
motor. The dust bag (30) can be emptied via the zip on
the underside.
10.2.1
Connection to an external dust
extraction system
1. Connect the suction hose to the dust extraction.
2. The dust extraction system must be suitable for the
material to be processed.
3. Use a special extraction device to extract dusts that
are particularly harmful to health or carcinogenic.
10.3 Fine adjustment of the stop for
90° chop cut (Fig. 1, 7)
Tool required:
• Allen key, 6 mm (C)
• 90° engineers square (A)*
• Phillips screwdriver*
• Open-ended spanner, size 13 mm*
* = not included in the scope of delivery!
1. Lower the saw head (6) and fix it with the locking pin
(34).
2. Loosen the locking screw (24).
3. Place 90° engineers square (A) between saw blade
(8) and rotary table (18).
4. Loosen the locknut (35a).
5. Adjust the adjustment screw (35) until the angle be-
tween the saw blade (8) and the rotary table (18) is
90°.
6. Re-tighten the locknut (35a).
7. Then check the position of the angle display. If nec-
essary, loosen the pointer (16) with a Phillips screw-
driver, set the scale (17) to 0° position and re-tight-
en.
10.4 Fine adjustment of the stop for
45° mitre cut (Fig. 1, 8)
Tool required:
• 45° engineers square (B)*
• Open-ended spanner, size 13 mm*
• Phillips screwdriver*
* = not included in the scope of delivery!
1. Lower the saw head (6) and fix it with the locking pin
(34).
10
|
GB / IE / NI
2. Fix the rotary table (18) in the 0° position.
ATTENTION
For mitre cuts (inclined saw head), the moveable stop
rail must be fixed in the outer position (left side).
3. Loosen the locking screw (23) on the moveable stop
rails (11) and slide the sliding stop rails (11) out-
wards to create a 45° stop angle (B) between the
saw blade (8) and the rotary table (18).
4. The moveable stop rails (11) must be locked in a po-
sition that the distance between the stop rails (11)
and the saw blade (8) is at least 8 mm.
5. The sliding stop rail (11) must be in the inner posi-
tion (right side).
6. Before making the cut, check that no collision could
occur between the moveable stop rails (11) and the
saw blade (8).
7. Loosen the locking screw (23) and tilt the saw head
(6) to the left, to 45°, using the handle (14).
8. Place 45° engineers square (B) between saw blade
(6) and rotary table (18).
9. Loosen the counternut (36a) and the adjustment
screw (36) until the angle between the saw blade (8)
and the rotary table (18) is exactly 45°.
10. Tighten the counternut (36a) again.
11. Then check the position of the angle display. If nec-
essary, loosen the pointer (16) with a Phillips screw-
driver, set the scale (17) to 45° position and re-tight-
en.
11 Operation
11.1 Operating the clamping device
(25) (Fig. 1)
The height of the clamping device (25) can be adjusted
via the locking screw (25a).
1. Lower the clamping device (25) onto the workpiece.
2. Tighten the locking screw (25c).
3. Turn the knurled screw (25b) clockwise to clamp the
workpiece.
4. In order to loosen the workpiece, proceed in reverse
order.
Advertenties
Hoofdstukken
Inhoudsopgave
