Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
11.2 Cutting depth limit (groove
sawing) (Fig. 1, 9)
WARNING
Risk of kick-back!
When making grooves, it is particularly important that
no lateral pressure is exerted on the saw blade. Other-
wise the saw head could suddenly kick up!
–
Use a clamping device when making grooves.
Avoid lateral pressure on the saw head.
1. The cutting depth can be seamlessly adjusted with
the screw (31). Loosen the knurled nut (31a) on the
screw for this. Set the desired cutting depth by screw-
ing in or unscrewing the screw (31). Then retighten
the knurled nut (31a) on the screw (31).
2. Check the setting with a test cut.
11.3 Switching the laser on / off (Fig.
19)
Switching on:
1. Press the laser ON/OFF switch (4) 1x. A laser line is
projected onto the workpiece to be cut, indicating
the exact cutting path.
Switching off:
1. Press the laser ON/OFF switch (4) again.
11.4 Serial cuts (Fig. 1, 10)
For repeated cuts of the same length, the length stop
(22) can be opened. You can use the length stop (22)
on the right and on the left.
1. Fold up the length stop (22).
2. Loosen the locking screw for the workpiece support
(20).
3. Pull out the workpiece support (21).
4. Set the required dimension between saw blade (8)
and length stop (22).
5. Re-tighten the locking screw for the workpiece sup-
port (20).
6. Carry out the cuts as described in 11.5, 11.6, 11.7
and 11.8.
11.5 Chop cut 90° and rotary table 0°
(Fig. 1, 11, 12)
In the case of cutting widths up to approx. 100 mm it is
possible to fix the sliding function of the saw with the
locking screw (23) in the rear position. In this position
the saw can be operated in chop cutting mode. If the
cutting width is over 100 mm then it is necessary to en-
sure that the locking screw (23) is loose and the saw
head (6) can move.
ATTENTION
For 90° chop cuts, the moveable stop rail must be
fixed in the inner position.
Hints for clamping:
• Do not work with workpieces that are to small to be
clamped in place.
• Reinforce very thin workpieces by sawing through
them together with an additional bar. Very thin
workpieces may "flutter" or break when sawing
1. Loosen the locking screw (23) for the moveable stop
rail (11) and push the moveable stop rail (11) in-
wards.
2. The moveable stop rail (11) must be locked in a po-
sition far enough from the inner position that the dis-
tance between the moveable stop rail (11) and the
saw blade (8) is no more than 8 mm.
3. Before making the cut, check that no collision could
occur between the moveable stop rail (11) and the
saw blade (8).
4. Tighten the set screw (23) again.
5. Move the saw head (6) to the upper position.
6. Use the handle (1) to push back the saw head (6)
and fix it in this position if required (dependent on
the cutting width).
7. Place the wood to be cut against the stop rail (12)
and on the rotary table (18).
8. Secure the material with the clamping device (25) on
the fixed saw table (19) to prevent it from shifting
during the cutting process.
9. Unlock the locking switch (3) and press the on/off
switch (2) to switch the motor on.
10. Move the saw head (6) with the handle (1) evenly
and with light pressure downwards until the saw
blade (8) has cut through the workpiece.
11. When the sawing process is finished, return the saw
head (6) to the upper resting position and release
the ON/OFF switch (2).
ATTENTION
The return spring automatically raises the product. Do
not release the handle after finishing cutting but allow
the saw head to move upwards slowly and with a little
counterpressure.
11.5.1
With the slide rail fixed (28) (Fig. 4)
1. Fix the saw's sliding function with the locking screw
for slide rail (28a) in rear position.
2. Move the saw head (6) with the handle (1) evenly
and with light pressure downwards until the saw
blade (8) has cut through the workpiece.
GB / IE / NI
|
11
Advertenties
Hoofdstukken
Inhoudsopgave
