Seal Chamber; Repair Work; General; Replacing Various Parts Of The Pump - Homa TP 28 Originele Handleiding
Verberg thumbnails
Zie ook voor TP 28:
- Originele handleiding (30 pagina's) ,
- Originele montage- en bedrijfshandleiding (28 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
defective. Please consult your manufacturer. When using
sealing chamber or leakage monitoring, in the event of a
defective seal, the display will light up again within the
next 4 weeks after the exchange.
Generally, the following applies when changing oper-
ating fluid: Turn off machine, allow it to cool, disconnect
from the power supply (to be carried out by a specialist!),
clean and place on a solid surface in a vertical position.
Warm or hot operating fluid may be under pressure.
The emergent operating fluid may cause burns. There-
fore, allow the machine to cool to ambient tempera-
ture first! Secure against tipping over and/or sliding!
6.4. Seal chamber
Since there is a large number of variants and versions of
these pumps, the exact location of the locking screws var-
ies depending on the pump part used.
•
Carefully and slowly unscrew the sealing chamber's
filler screw.
Attention: The operating fluid may be under pressure!
•
Unscrew drain screw. Drain the operating fluid and
collect in a suitable container. Clean the drain screw,
equip with a new seal ring and tighten again. To drain
fully, the machine must be tipped slightly to the side.
Ensure that the machine cannot tip over and/or slide
away!
•
Place machine horizontally and fill with operating
fluid. Observe the prescribed operating fluid and fill
quantities.
•
Clean the filler screw, equip with a new seal ring and
tighten again.
7. Repair work
7.1. General
The following repair work may be done on this machine:
•
Change of impeller and pump chamber
In general, the following should always be heeded when
doing this work:
•
O-ring seals and existing seals must always be re-
placed.
•
Screw locking devices such as spring washers must
always be replaced.
•
Torque values must be complied with.
The following general guidelines apply to repair
work: Switch the machine off, disconnect it from the
grid, clean it and lay it in a horizontal position on a
firm supporting surface. Secure it against falling over
and/or slipping away!
Unless stated otherwise, the torque values in the Tables
should be used. Values for clean, lubricated screws.
Tightening torque [Nm] for A2/A4 screws (friction coeffi-
cient = 0.2)
A2/A4,
strength 70
DIN912/DIN933
M6
7 Nm
M8
17 Nm
M10
33 Nm
M12
57 Nm
M16
140 Nm
M20
273 Nm
7.2 Replacing various parts of the pump
Change impeller and pump unit
•
Loosen and remove the screws on the sealing hous-
ing.
•
Secure and remove the pump housing from the seal-
ing housing with suitable equipment, e.g. hoisting
gear. Place on a secure base.
•
Fasten the impeller with suitable equipment, loosen
and remove the impeller fastening (cylindrical screw
with socket hex).
Pay attention to the screw locking device!
•
Remove the propeller from the shaft with a suitable
puller.
•
Clean the shaft
•
Attach new propeller to the shaft.
Ensure that the mating surfaces are not damaged!
•
Insert a new propeller attachment (cylinder head
screw with a hexagon socket and a new screw lock-
ing device) into the shaft. Firmly fix the propeller and
tighten the cylinder screw.
A2/A4,
strength 80
DIN912/DIN933
11.8 Nm
28.7 Nm
58 Nm
100 Nm
245 Nm
494 Nm
ENGLISH | 43
Advertenties
Hoofdstukken
Inhoudsopgave
Probleemoplossen
