Advertenties
Beschikbare talen
Beschikbare talen
• Move the shaft of the cutting device into the sleeve of the extension
attachment (22).
• Gently turn the shaft until the locking pin (18 or 27) engages.
• Now tighten the locking screw (25).
The cutting device is disassembled in reverse order.
10.2 Attach the carrying strap (35) (Fig. 12-14)
The petrol combination device must be used with the carrying strap (35).
• Attach the carrying strap (35) (see Fig. 13 and 14).
• Adjust the length of the belt so that the carabiner hook (a) is approx.
one hand-width beneath the right hip.
• You can attach the petrol combination device to the carrying strap
(35) in different positions depending on the attachment device and the
fill level of the fuel tank (8).
• Hook the petrol combination device in a suitable position to the lifting
eye (2) using the carabiner hook.
• Allow the petrol combination device to swing.
Attention!
• The cutting tool on the brushcutter / grass trimmer (12) must not touch
the floor in the normal working position.
• When using the hedge trimmer (17) or pole pruner (26), the petrol
combination device should be swung horizontally.
• Do not start the petrol combination device while it is hooked to the
carrying strap! Only hook the device to the lifting eye (2) using the
carabiner hook (a) of the carrying strap with the engine running.
Safety latch on the carrying strap
• ATTENTION! In an emergency, the safety tab (b) on the carrying
strap (35) can be pulled. The machine then immediately detaches
from the carrying strap (35) and falls to the floor.
10.3 Fill with fuel
m Risk of injury! Petrol is explosive!
Switch off the engine and allow it to cool!
Wear safety gloves!
Avoid skin and eye contact!
You must observe the "safety instruction" section.
• Only refuel the tank outdoors or in sufficiently ventilated rooms.
• Clean the area surrounding the tank plug of the fuel tank (8). Impuri-
ties in the tank lead to operational faults.
• Before refuelling, shake the container with the fuel mixture.
• Carefully open the tank plug of the fuel tank (8) so that any possible
excess pressure can be relieved.
• Carefully fill the fuel mixture up to the lower edge of the fuel tank (8)
filler neck. Use a funnel or a filling aid to prevent spilling of the fuel.
• Close the tank plug of the fuel tank (8) again. Ensure that the tank cap
is tightly sealed.
• Clean the tank cap and the surroundings.
• Check the fuel tank (8) and fuel lines for leaks.
• Move at least three meters away from the refuelling area before start-
ing the engine.
10.3.1 Drain the fuel
Only empty the fuel tank (8) outdoors or in well-ventilated
rooms. Make sure that no fuel gets into the soil (environ-
mental protection). Use a suitable surface.
• Hold a collection container under the fuel tank (8).
• Unscrew and remove the tank plug of the fuel tank (8).
• Drain the petrol/oil mixture completely.
• Retighten the tank plug by hand.
11. Operation
Never operate the engine drive unit (1) without the brush
cutter / grass trimmer (12), hedge trimmer (17) or pole
pruner (26).
11.1 Starting the device
Do not start the device until you have fully assembled it.
m Risk of injury!
Only start the petrol combination device when a cutting
device is connected! Remove the corresponding transport
protection and inspect the device to ensure that its operat-
ing status is good.
Never use a cutting device that is damaged, poorly adjust-
ed or maintained, or not fully mounted and secured.
Check before use!
Check that the device is in a safe condition:
• Check the device for leaks.
• Check the device for visible damage.
• Check that all parts of the device are securely attached.
• Check that all safety devices are in good condition and functional.
11.1.1 Starting (Fig. 1, 15)
Once the device is properly assembled, start the engine as follows:
Starting the engine when cold:
1.
Press the on/off switch (3) to the on position "I".
2.
Turn the choke lever (60) to the position.
3.
Press the fuel pump (61) 7 times.
4.
Pull the handle of the starter cable (7) 3 to 5 times to start the
motor.
ATTENTION! Never put a foot on the engine drive unit (1) or kneel
on it.
5.
When the engine is running, wait a moment and then briefly rev up
using the throttle (9). The choke lever (60) automatically moves to
the position
.
6.
To start the cutting device, press the switch lock (4) with the palm
and the throttle with the fingers (9). The further you push the throt-
tle lever, the higher the engine speed. Loosening the throttle grip
brings the engine back into idling and the cutting tool stops. The
cutting tool must not rotate or move while idle!
7.
If problems occur, switch the on/off switch (3) to "0" immediately
so that the motor stops.
Attention! The cutting device can keep turning for a few seconds.
Starting the engine when warm
1.
To start the motor when warm, move the choke lever to the "Warm
start and working" position.
2.
Pull the handle of the starter cable (7) 3 to 5 times to start the
motor.
ATTENTION! Never put a foot on the engine drive unit (1) or kneel
on it.
.
.
GB/IE/NI
15
Advertenties
