Inhoudsopgave
Advertenties
Setting fuel tank capacity
1 – 10
1
3
3
5
6
2
3
5
6
7
8
4
3
(only for cars operated with speed controllers)
The setting of the fuel tank capacity in combination with the Pit Lane
(20030356) is effected for all cars simultaneously. The setting can
5
6
be carried out on 10 levels with the 5 LEDs indicating the different
levels by flashing or permanent lighting.
1 LED lights = low fuel capacity
1
5 LEDs light = full tank
2
4
Switch on the Control Unit, place the cars to be adjusted on the
track and activate the fuelling function by means of the slide switch
2
, fig.
. Press the "FUEL" button
3
LEDs will now light, showing the fuel capacity last used. Push the
5
7
"FUEL" button
as many times until you have reached the fuel
capacity desired. Confirm by pressing "ENTER/START"
running light and the lighting of the middle LED confirms completion
4
of the setting, fig
.
6
Extended fuelling function
You can choose between 3 modes via the sliding switch
fig.
:
3
5
• OFF = cars don´t consume any "petrol"
• ON = cars consume "petrol"
• REAL = maximum speed depending on fuel tank capacity / cars
consume "petrol") (only in combination with Pit Lane 20030356 or Pit
Stop Lane 20030346 and Pit Stop Adapter Unit 20030361)
When driving in "REAL-mode" the car with a full tank is "heavier", drives
slowlier and shows a lower braking effect; a car with an empty tank is
"lighter", drives faster and shows a higher braking effect. The current
fuel tank capacity and the "fuel consumption" can only be displayed in
combination with the Driver Display 20030353 and Pit Stop 20030356.
Refuelling of cars with Pit Lane 20030356
and Driver Display 20030353
Pit Lane 20030356
4
7
5
4
5
9
The car´s present tank capacity can be read via the bar display with
5 green and 2 red LEDs at the Driver Display. For refuelling drive
your car into the Pit Lane across the refuelling sensor fig.
bar display now starts to flash, fig.
by keeping the lane-change button pushed. fig.
refuellings are indicated by flashing or lighting of the yellow LEDs,
fig.
(also see Driver Display).
10
Note: cars with an empty tank are disregarded for lap-counting
in combination with Position Tower 20030357.
Setting of tank capacity at the start of the race
Pit Lane 20030356
14
11
1 – 10
2
4
13
5
2
1
4
(only in combination with Pit Lane 20030356 and Driver Display
20030353)
Irrespective of the basic setting of the tank capacity it is possible
to individually set the tank capacity for one or several cars at the
7
8
race´s start for the number of laps till the first pit stop. Push "START/
1
ENTER" once
nently, fig.
6
Clicking the lane-change button at the corresponding speed control-
ler enables you to change the fill level, fig.
2
1
Deactivating Settings Keys
4
7
8
1
5
3
2
7
once. A certain number of
3
6
7
3
. A short
3
2
2
,
To deactivate the keys for setting Speed, Brake and Fuel, proceed
as follows: Hold down the Code Key:
6
7
While holding down the Code Key
then release the Code Key. To reactivate the above keys, repeat the
procedure just described.
Extended Pit Lane function
Pit Lane 20030356
1
Driver Display 20030353
3
2
3
8
6
7
3
2
5
6
7
10
(only in combination with Pit Lane 20030356)
It is possible to activate/deactivate the lap counting function in the Pit
Lane 20030356 or Pit Stop Lane 20030346 with the Pit Stop Adapter
Unit 20030361. Switch off the Control Unit, keep "SPEED" button
pushed, switch on Control Unit and release "SPEED" button
. The
By pushing the button again, 1 or 2 LEDs will light depending on
7
, and the car can be refuelled
the setting.
8
. The number of
9
• LED 1 = lap counting function deactivated
• LED 1 + 2 = lap counting function activated
Select the desired setting and push or drive a car across the Pit
Lane Sensor, fig.
"START/ENTER"
Driver Display 20030353
12
3
2
14
4
3
6
7
5
6
4
3
3
; the 5 LEDs at the Control Unit will light perma-
, and the Driver Display´s bar display will flash, fig.
12
5
6
.
14
3
2
4
3
6
7
8
1
5
6
8
4
3
1
5
6
8
8
, turn on the Control Unit and
2
5
1
4
8
1
5
6
8
4
3
5
6
5
. The settings will now be adopted. Push
3
for leaving the settings again.
Sound ON/OFF
1
1
2
1
4
8
3
7
8
5
2
1
The confirmation sound when crossing the sensors and the key
sound can be switched off. Switch off the Control Unit and keep the
.
"START/ENTER" button
3
13
7
8
release "START/ENTER"
3
for switching on the Control Unit cannot be switched off however.
Reset function
1
2
1
3
7
8
2
1
To restore the Control Unit to factory settings the Control Unit offers a
reset function. Switch off the Control Unit and keep the "ESC/PACE
CAR"
4
button pushed; switch on the ractrack and release the but-
7
8
ton again. All previous settings for speed, braking performance, tank
fuel capacity, sound and lap counting will be restored to factory set-
tings. The cars´ settings will remain unaffected by this measure unless
they are placed on the racetrack.
Factory settings:
• speed = 10
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
Energy-saving mode
3
2
After 20 minutes of non-usage the Control Unit switches to ener-
gy-saving mode and all displays such as Position Tower, Driver
Displays and Startlight are turned off. To reactivate the controller,
switch it off for 2 or 3 seconds, then switch it on again. All settings
will be kept.
6
7
3
2
Replacement of double sliding
contact and guide keel
6
7
1
2
1
7
8
2 a
2 b
5
)
5
.
Advice:
• It is recommended to always take out and change only one grinder.
• Never pull the vehicle backwards, because the grinders could be
damaged otherwise.
Please carefully pull out the guide keel according to fig.
1
When changing the double contact brushes please take care
2
that in stage one the upper contact brush
partly and that in stage two the double contact brush can be pulled
2
3
6
7
pushed, switch on the racetrack and
again. The acknowledgement sound
2
4
3
5
6
1
8
1
8
.
1
is only pulled out
2 a
2
Advertenties
Hoofdstukken
Inhoudsopgave
