Inhoudsopgave
Advertenties
6 .1
Using the hand transmitter
The hand transmitter works with a rolling code that changes
with each sending procedure. Each hand transmitter button
is assigned to a rolling code.
To control a receiver, you must teach in the desired hand
transmitter button (see section 4.4 or the instructions
of the receiver).
6 .1 .1
Control elements
See Figure 9
▶
1
LED
2
Hand transmitter buttons
3
3 V battery, type CR 2025, lithium
6 .1 .2
Inserting / changing the battery
3 V battery, type CR 2025, lithium
See figure 9
▶
Only use the battery type CR 2025, 3 V Li, and pay
▶
attention to the correct polarity.
WARNING
Risk of explosion due to incorrect battery type
There is the risk of explosion if the battery is replaced with
an incorrect battery type.
Only use the recommended battery type.
▶
ATTENTION
Destruction of the hand transmitter by leaking batteries
Batteries can leak and destroy the hand transmitter.
Remove the battery from the hand transmitter if it is out
▶
of use for a long period of time.
6 .1 .3
LED displays
LED
The rolling code is transmitted
illuminated
LED
The battery is almost empty.
flashing
The battery should be replaced soon.
LED is not
The hand transmitter is not functioning.
responding
•
Check whether the battery has been
inserted correctly.
The battery is empty and must be
•
replaced immediately.
6 .2
Excerpt from the declaration of conformity for
the hand transmitter
Conformity of the abovementioned product with the
requirements of the Radio Equipment Directive (RED)
2014/53/EU was verified by compliance with the following
standards:
•
EN 60950:2000
•
EN 300 220-1
•
EN 300 220-3
•
EN 301 489-1
•
EN 301 489-3
The original declaration of conformity can be requested from
the manufacturer.
437784 B3 / 28-2021 / RE
7
Integrated radio receiver
The garage door operator is equipped with an integrated radio
receiver. It can only be taught in or deleted when the operator
is at a standstill.
A maximum of 6 different hand transmitter buttons can be
taught in. If more are taught in, the first one will be deleted
without advance warning.
In the delivery condition all memory spaces are empty.
7 .1
Excerpt from the declaration of conformity for
the receiver
Conformity of the abovementioned product with the
requirements of the Radio Equipment Directive (RED)
2014/53/EU was verified by compliance with the following
standards:
•
EN 300 220-3
•
EN 301 489-1
•
EN 301 489-3
The original declaration of conformity can be requested from
the manufacturer.
8
Operation
Danger of injury during door travel
If people or objects are in the area
around the door while the door is in
motion, this can lead to injuries or
damage.
Make sure that children are not
▶
playing near the door system.
Make sure that no persons or
▶
objects are in the door's area of
travel.
If the door system has only one
▶
safety feature, only operate the
garage door operator if you are
within sight of the door's area of
travel.
Monitor the door travel until the
▶
door has reached the end-of-travel
position.
Only drive or pass through remote-
▶
control door systems when the door
is at a standstill!
Never stay standing under the
▶
open door.
Danger of crushing in the boom
Do not reach into the boom with your fingers during door
travel, as this can cause crushing.
Do not reach into the boom during door travel.
▶
Danger of injury from the cord knob
If you hang on the cord knob, you may fall and injure
yourself. The operator could break away and injure persons
or damage objects that are located underneath. The
operator itself can be destroyed.
Do not hang on the cord knob with your body weight.
▶
ENGLISH
WARNING
CAUTION
CAUTION
83
Advertenties
Hoofdstukken
Inhoudsopgave
