the batteries in the compartment for too long can cause leaking which can damage the device.
ATTENTION:
• Does not contain parts which can be repaired by the user. The warranty does not cover batteries or
damage caused by old batteries.
• Only use good quality batteries. Always use new batteries and do not use old and new batteries
together. Use batteries of the same brand and of the same type.
Battery disposal: Exhausted batteries are to be disposed of in the appropriate recipient.
2. Instructions for use
• Before each usage, wash hands thoroughly and clean the nasal douche and its accessories as
indicated in paragraph 3. Cleaning, Sanitization, Disinfection and Sterilization.
• During application it is advisable to be careful as the solution can drip from the nose.
2.1 - Before usage place batteries as indicated in paragraph 1.
2.2 - For a correct use of the nasal douche, the symbol of the little man ( ) (4c), placed on the flask (4),
always has to be directed towards the patient. The flask can be fixed on the position of the little
man on the side of the activation button (5a) allowing activation of the nasal douche with the
thumb, or with the little man on the opposite side of the button in order to allow activation with
the index finger.
In order to obtain one of the aforementioned conditions, when screwing the flask clockwise (4) on
the douche compressor body (5) (fig C.), the symbol of the little man needs to be located on the
side opposite to the position you would like to obtain (fig. C).
2.3 - Pour the solution (max 15 ml) in the nebulisation slot (4a) of the flask, as shown in (fig. E). Verify
the presence of the atomizer (3).
2.4 - Apply the separator (2) directing it with the dot (2a) in correspondence with the little man ( ) (4c)
located on the external part of the flask (4), as shown in (fig F.). Then insert the most suitable nasal
adaptor for the size of your nasal openings (1A-1B-1C)
2.5 - Insert the hole of the nasal adaptor in one nasal opening (fig. G).
2.6 - Activate the nasal douche by keeping the activation button pressed (5a) during the inhalation
phase and release it before exhaling; in this phase, in order to help the discharge of the mucus,
gently blow through the nasal opening that has been treated with the nasal douche, keeping the
other nasal opening closed.
2.7 - During nebulisation it is advisable to close the other nostril where the douche is not being
applied, with a finger.
2.8 - Repeat procedures 2.5 to 2.7 for the other nasal opening as well, trying to evenly distribute the
solution in the two nasal openings.
2.9 - In the case of children or people who are not self-sufficient, or not able to perform the various
phases of point 2.6, it is advisable to carry out the application alternating the two nasal openings
after about 15 seconds, with breaks necessary to allow for the discharge of mucus.
2.10 - In case of medicine administration through aerosol, it is advisable to carry out a wash with a
saline solution first, in order to obtain a more efficient distribution of the medicine on the nasal
mucous membrane.
2.11 - At the end of the application, turn off the device and carry out cleaning and/or sanitizing
following the instructions in paragraph 3. Cleaning, Sanitization, Disinfection and Sterilization.
3. Cleaning, Sanitization, Disinfection and Sterilization. (For clinical
or hospital use only)
A thorough cleaning is extremely important for the lifespan and well-functioning of the device.
After usage, unassemble the nasal douche by following the drawing (see fig A), remove the
batteries and procede with cleaning and/or sanitizing of the components performing the
following operations:
3.1 - Cleaning: Irrigator compressor body
For component (5) only use a damp cloth with antibacterial detergent (non-abrasive and solvents
free).
The nasal douche has an aspiration valve (5c) which is to be cleaned when dirty. To access the valve
lift the lid of the battery compartment and remove the valve by lifting it with a ballpoint pen (fig
H); then wash the valve with water and detergent. Before reassembling, make sure that the valve is
8