Advertenties
Beschikbare talen
Beschikbare talen
GHE 250.0/GHE 250.0 S:
Sound pressure level
92/90 dB(A)
at workplace L
pA
Uncertainty K
3 dB(A)
pA
Screw tightening torques:
Blade disc
50 Nm
Reversible blade
10 Nm
2
Shredding blades
10 Nm
Weight
27/27 kg
27/27 kg (GB)
26 kg (CH)
L/W/H
107/48/143 cm
GHE 260.0/GHE 260.0 S:
Motor, type
BSRF 0.75/2-C
Power
2900 W
Amperage rating
4.8 A
Rated voltage
400 (3~) V~
Speed
2780 rpm
Fuses
10 A
Frequency
50 Hz
Protection class
I
Type of protection
Splash proof
(IP X4)
Operating conditions
P40
40 s load time
60 s idle time
Measurement in accordance with
2000/14/EC / S.I. 2001/1701:
Guaranteed sound
102/101 dB(A)
power level L
WAd
GHE 260.0: Uncer-
3,2 dB(A)
tainty K
WA
GHE 260.0 S: Uncer-
3,3 dB(A)
tainty K
WA
Measurement in accordance with EN
50434:
0478 201 9913 D - EN
GHE 260.0/GHE 260.0 S:
Sound pressure level
89/91 dB(A)
at workplace L
pA
Uncertainty K
3 dB(A)
pA
Screw tightening torques:
Blade disc
50 Nm
Reversible blade
10 Nm
2
Shredding blades
10 Nm
Weight
27/27 kg
L/W/H
107/48/143 cm
1)
Attention!
Mains fuses of less than 16 A may
frequently trip during start-up of the
machine or when it is operating
under heavy load.
2)
for models GHE 250.0 and
GHE 260.0
17.1 REACH
REACH is an EC Regulation for the
registration, evaluation, authorisation and
restriction of chemicals.
Information on compliance with the
REACH Regulation (EC) No. 1907/2006 is
available from www.stihl.com/reach.
18. Troubleshooting
If necessary, contact a specialist
dealer; STIHL recommends STIHL
specialist dealers.
Fault:
Motor does not start
Possible cause:
– Motor overload protection activated
– No mains voltage
– Electric cable, plug, plug connector or
switch defective
– Feed chute not properly closed - safety
cut-off switch actuated (motorstop)
– Blade disc blocked
– Locking device is not reset
Remedy:
– Allow machine to cool down ( 8.6)
– Check power cable and fuse
( 10.1)
– Check cable, plug, connector and
switch and replace if necessary (by
electrician) ( 10.1)
– Close feed chute properly and tighten
screws ( 11.2)
– Remove feed chute and remove
shredder deposits from the housing
(Important: disconnect the power cable)
( 11.3)
– Reset locking device ( 11.4)
Fault:
Reduced shredding performance
Possible cause:
– Blunt blades
Remedy:
– Reverse, re-sharpen or replace
shredding blades ( 11.7)
Fault:
Shredding material is not drawn in
Possible cause:
– GHE 260: Incorrect rotational direction
of blade disc
Remedy:
– GHE 260: Change rotational direction
of blade disc ( 10.6)
51
Advertenties
