Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
When the wheel is binding or when
interrupting a cut for any reason, switch
off the power tool and hold the cutting
unit motionless until the wheel comes to a
complete stop. Never attempt to remove
the wheel from the cut while the wheel is
in motion otherwise kickback may occur.
Investigate and take corrective action to
eliminate the cause of wheel binding.
Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel may
bind, walk up or kickback if the power tool is
restarted in the workpiece.
˜ Assembly
WARNING! DANGER OF FIRE!
Assemble and use the product on a
fire-resistant surface only.
Follow these steps:
1. Fasten the saddle
plate
with the hexagonal socket head
[
]
screws
and washers
[
]
key
(Fig. 1).
[
]
2. Fasten the handle
with the projecting screw thread and the
corresponding nut (Fig. 2).
3. Push the plastic locating pieces
mounting pieces
[
the mount
(Fig. 3).
[
]
4. Attach the mounting pieces
the plastic locating pieces
hexagonal socket head screws
elongated holes in the mount
5. Insert the adjustment screw
bottom hole and the adjustment screw
through the top hole of the mount (Fig. 4).
Note that later the rubber buffers of these
screws must lie against the angle grinder
housing.
Note: First insert these screws so that the
rubber buffers lie directly against the mount
.
[
]
on to the base
[
]
with the hex
[
]
on to the mount
[
3 ]
[
of the
[
]
,
on to the guide of
]
[
]
,
through
[
]
[
]
with the
[
]
in the
[
]
(Fig. 3).
[
]
through the
[
]
1 ]
[
Note: Bear in mind that the angle grinder
must be fitted with a suitable cutting disc
before assembly. It is not possible to change
the disc with the angle grinder installed in
the product.
6. Prepare for mounting the angle grinder in
the mount
[
Note: First check the size of the handle
thread of your angle grinder. The size may
be M6, M8 or M10.
7. Place the corresponding mounting bolts
washers
7 ]
[
pieces
and plastic bushings
[
]
side, ready for use.
8. Insert the necessary plastic bushings
the mounting pieces
Note: Ensure that the size of the plastic
bushings
[
6 ]
bolts
. Plastic bushings are not required
8 ]
[
for mounting bolts M10
9. Place the desired distance piece
washer on the mounting bolt
]
Note: The 3 distance pieces
choosing the most appropriate cutting depth.
Note: Set the distance piece
the cutting disc cannot come into contact
with the workbench/table below the base
plate
(Fig. 7).
[
]
10. Screw the matching mounting bolt
through the mounting pieces
angle grinder by wrench
11. Fasten the angle grinder in place by
tightening the corresponding size of nut
on the mounting bolt
the direction of the mounting piece pieces
,
(Fig. 6).
[
]
[
]
12. Set the adjustment screws
angle grinder is aligned at right angles to
the base plate
mount
(Fig. 6).
[
]
.
]
and matching nuts
, distance
9 ]
[
[
6 ]
,
(Fig. 5).
[
]
[
]
matches the required mounting
.
8 ]
[
[
(Fig. 7).
8 ]
[
are for
[
]
so that
[
]
[
8 ]
,
[
]
[
(Fig. 6).
[
]
(i.e. by turning it in
[
8 ]
,
so that the
[
1 ]
[
]
and firmly attached to the
[
]
GB/IE/NI
,
[
8 ]
to one
into
6 ]
[
and
]
7 ]
[
and the
]
9 ]
[
11
Advertenties
Hoofdstukken
Inhoudsopgave
