Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Extraction tower:
Switch on 10 cm
Briefly press
Switch on 30 cm
Press and hold
for 2 seconds
Switch AUTO on 20 cm
Press
Switch on run-out function
Press and hold
for 2 seconds
Switch off
Briefly press
AUTO function: Preset function where the extraction tower
immediately comes into position at the most common cooking
height of 20 cm. The extraction mode 5 (3rd led) is automatically
set.
Run-out function: This function starts at the end of cooking.
For a fixed time, the remaining cooking vapours will be extracted
from the kitchen by the extraction tower at low extraction mode
and at a height of 10 cm. When recirculation is selected, the
recirculation filters are also dried.
The run-out time is set to 30 minutes by default in the recirculation
mode and 10 minutes in exhaust mode. It is recommended that
this function be allowed to carry out its function completely. At
the end of the run-out time, the motor and the extraction tower
will automatically switch off and the tower will close.
6.4 Increase and decrease the power level
The extraction tower can be set to 8 power levels, with 3 intense
levels (6, 7 and 8).
Activate the intense levels when cooking food with a strong
smell or vapour. On higher flow rates, the extraction tower works
for a fixed period of time: 1 hour on position 6, and 6 minutes on
position 7 and 8 if the device is set to exhaust mode. After this
time, the extraction tower switches back to position 5.
Adjusting the power level:
Increase the power
+
Press
Decrease the power
‐
Press
6.5 Auto-stop
In order to ensure the extraction does not keep running, the
motor switches off and the extraction tower closes automatically
after 3 hours (if the controller has not been changed during
these 3 hours).
9 Cleaning indications
Display
1st LED
9.1 Cleaning indication for grease filter
lights up
1st LED
Indication: LED next to
lights up
3rd LED
After 20 cooking hours, the LED next to the
lights up
light up.
Follow the cleaning instructions as described in the
1st LED
chapter, Cleaning.
blinks
LED
After having cleaned and replaced the grease filters, reset the
off
cleaning indication.
Reset: press the
9.2 Cleaning indication for Monoblock
recirculation filter (only with recirculation)
Indication: LED next to
After a fixed time, the LED lights up next to the symbol
will light up. This indication indicates that the recirculation filter
needs to be regenerated.
Follow the cleaning instructions described in the
recirculation box / filter manual.
After the regeneration and after having replaced the recirculation
filter, reset the cleaning indication.
Reset: press the
9.3 I/O module connection
The device can be optional equipped with the Input/Output
module n° 990036.
When the input of the module is used in "closed" input situation
the extraction tower will move to the desired height only the
extraction will not start.
The leds next to the Cleaning indication
The extraction only starts when the input situation is "open".
The input can be used for example in combination with a
sinwow switch in duct out mode.
When the output of the module is used the relay will close when
Brighter
the extraction is active.
LED(s)
The output remains closed also 5 minutes after closing the
extraction tower.
LED(s)
dim
8 Cooking advice
Quality of the pots and pans
Suitable cookware, pots and pans include: steel, enamelled
steel, cast iron, stainless steel with magnetic base, aluminium
with magnetic base (±100mm min). Unsuitable pans include:
– 73 –
lights
control key for 3 seconds.
lights
control key for 3 seconds.
and
symbol will
will blink.
Advertenties
Hoofdstukken
Inhoudsopgave
