Inhoudsopgave
Advertenties
grass grows and the hardness of the soil.
Keep the underside of the equipment clean and
remove soil and grass build-up. Deposits make it
more diffi cult to start the aerator and decrease the
quality of the scarifying.
Always scarify along inclines (not up and down).
Switch off the motor before doing any checks on
the roller.
Danger!
The cutting unit is equipped with moving blades
and will rotate for a few seconds after the motor is
switched off .
Never attempt to stop the roller.
Tips on aerating properly with the aerator
roller available as an option.
The way of working for aerating is the same as for
scarifying.
You should therefore observe these safety inst-
ructions and notes on working practice.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the safety plug before performing
any adjusting, repair, maintenance or cleaning
work on the equipment. Make sure that the spike
drum is not rotating.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
•
A worn out or damaged cutting unit should be
replaced by an authorised expert.
•
Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you
Anl_GC_SC_18_28_DS_Li_SPK13.indb 23
Anl_GC_SC_18_28_DS_Li_SPK13.indb 23
GB
can work safely with the scarifier.
•
Store the scarifier in a dry place.
•
For longer life, all screw-fastened parts, such
as wheels and axles should be cleaned and
subsequently oiled.
•
Regular servicing of the scarifier not only
secures longer endurance and performance,
but also contributes to an accurate and simp-
le scarification of your lawn.
•
At the end of the season, carry out a general
check of the scarifier, and remove all residue
collected. Before the start of every season, it
is absolutely necessary to check the state of
the scarifier. Contact our Customer Service if
repair work is necessary.
7.3 Changing the roller (see Figures 15-19)
Be sure to wear work gloves!
Only replace the roller with a genuine Einhell rol-
ler, as this will ensure top performance and safety
under all conditions.
To change the scarifi er roller or the optio-
nally available aerator roller (Fig. 17, Art. No.:
34.059.41), proceed as follows:
Remove the two socket head screws (Fig. 15 /
Item D). Lift the roller at this end (Fig. 16) and pull
it out in the direction of the arrow. If the holder
(Fig. 17 / Item E) does not exist on the roller you
want to install, remove it from the previously used
roller and fi t it on the roller you now want to use.
Slide the new roller in the direction of the arrow
(Fig. 19) onto the square-ended drive (Fig. 18 /
Item F) and then press it into the holder (Fig. 19).
Use the two socket head screws (Fig. 15 / Item D)
to secure the roller again.
Apply grease to the square-ended drive from time
to time so that the rollers can be changed easily.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Replacement cutting unit Art. No.: 34.059.42
Aerator roller Art. No.: 34.059.41
Catch basket Art. No.: 34.059.40
- 23 -
02.12.2024 13:00:42
02.12.2024 13:00:42
Advertenties
Inhoudsopgave
