Inhoudsopgave
Advertenties
2. Use the fastening screws (Item 14) and the
wing nuts (Item 13) to screw one tube (Item
4) securely on each push bar holder (Item 5 /
12).
3. Screw the upper push bar (Item 3) on each
tube (Item 4). Use the push bar fastening
screws (Item 14) and the wing nuts (Item 13)
similarly for this purpose.
4. Fasten the power cable to the push bar tubes
using the supplied cable clips (Item 11). Make
sure that the cable and cable clips do not
obstruct the push bar when it is fl ipped over
(see section 8).
Important! There are 3 assembly holes so that
the height of the push bar can be adjusted to spe-
cifi c user requirements at any time. Use the hole
which is best suited for you, making sure that you
use the same hole on both sides.
Please ensure that the ejector fl ap can be opened
and closed easily!
Fitting the optional catch basket
(see Fig. 7-8)
The basic version of the equipment does not in-
clude a catch basket. This is available separately
(Art. No. 34.059.40).
•
To hang the grass basket on the scarifier you
must lift the ejector flap (Item 10) with one
hand and with the other hand take hold of the
grass bag by the handle and hook it onto the
scarifier from above.
Danger!
Before you ever hook the grass basket to the sca-
rifi er you must ensure that the motor is switched
off and the cutting unit is not rotating.
Adjusting the working depth (see Fig. 9)
The scarifi er depth is adjusted at the two front
wheels using the adjustment mechanism. For this,
pull out the adjusting screw and turn the wheel to
the left or right into one of the available positions
(0/I/II/III).
The scarifi er depth must always be identically set
on both sides!
0 = drive/transport position
I = scarifi er depth 2 mm
II = scarifi er depth 4 mm
III = scarifi er depth 6 mm
Anl_GC_SC_18_28_DS_Li_SPK13.indb 21
Anl_GC_SC_18_28_DS_Li_SPK13.indb 21
GB
Charging the battery (Fig. 10)
The equipment is supplied without batteries and
without a charger!
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock buttons (Fig.
11/Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(22) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (21) into the battery
charger (22).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 11)
Press the switch for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
- 21 -
02.12.2024 13:00:41
02.12.2024 13:00:41
Advertenties
Inhoudsopgave
