Inhoudsopgave
Advertenties
4. Technical data
Idle speed .............................................3200/min
Protection class ................................................III
Voltage ................................................... 18 V DC
Working width ........................................... 28 cm
Number of blades ................... 12 double blades
Scarifying depth .......................... -2 / 2 / 4 / 6 mm
L
sound pressure level ....................... 67 dB(A)
pA
Uncertainty K .............................................. 3 dB
L
sound power level .......................... 87 dB(A)
WA
Uncertainty K .............................................. 3 dB
L
sound power level guaranteed ........ 90 dB(A)
WA
Vibration at the handlebars, max. ........... 3.7 m/s
Uncertainty K ..........................................1.9 m/s
Protection type .............................................IPX1
Weight ........................................................6.8 kg
Danger!
Sound and vibration
Sound and vibration values were measured in ac-
cordance with the standards EN 62841.
Important!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power X-Change
series!
The lithium-ion batteries of the Power X-Change
series are allowed to be charged only with the
Power-X charger.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
Anl_GC_SC_18_28_DS_Li_SPK13.indb 20
Anl_GC_SC_18_28_DS_Li_SPK13.indb 20
GB
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Damage to hearing if no suitable ear protec-
tion is used.
2. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
2
longed period or is not properly guided and
maintained.
2
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
5. Before starting the equipment
Warning!
Always pull out the safety plug before performing
any adjusting, repair, maintenance or cleaning
work on the equipment.
The scarifi er is delivered unassembled. The com-
plete push bar must be assembled and mounted
before using the scarifi er.
Follow the operating instructions step-by-step
and use the pictures provided as a visual guide to
easily assemble the machine.
Important! Required assembly parts (screws,
cable guides, etc.) or functional parts (e.g. plugs,
wrenches, etc.) can be found in the shaped parts
of the packaging or on the equipment.
Fitting the push bar holders and cable clips
(Fig. 3 - 6)
1. Screw the left push bar holder (Item 5) secu-
rely on the housing. Make sure that the em-
bossing (Fig. 2 / Item A) faces inwards. Then
screw on the right-hand push bar holder (Fig.
2 / Item 12) securely.
- 20 -
02.12.2024 13:00:41
02.12.2024 13:00:41
Advertenties
Inhoudsopgave
