Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
The product is only suited for use with the
built‑in LED control gear .
The product continues to draw a small amount
of power even if the product is off as long
as the product is connected to the supply
mains . To switch the product off completely,
disconnect the power plug
socket‑outlet .
Luminaries shall not be connected after each
other .
This is not a portable lamp . Disconnect the
power plug
from the socket‑outlet before
18 ]
[
moving the tripod .
˜ Before installation
NOTE: Remove all packaging materials from
the product .
The product may be placed on the provided
tripod
and then be positioned in the
12 ]
[
desired location .
Rotate the tripod locking screw
anti‑clockwise to loosen the tripod
Adjust the tripod
12 ]
[
Rotate the tripod locking screw
to fix the tripod in its position (Fig . M) .
Use and operate the product on a stable
surface without any angle .
Fully extend the tripod
stability of the product .
m
CAUTION! Note the position of your hands
whilst opening or closing the tripod
pinching your fingers (Fig . M) .
˜ Installation
Unscrew the pre‑installed fastening material
from the baseplate
This includes:
–
Handle fixing screws
[
1 ]
–
Handle spring washers
2 ]
[
–
Flat washers (handle)
3 ]
[
–
Spotlight fixing screws
[
4 ]
–
Flat washers
5 ]
[
–
Spring washers
[
6 ]
from the
[
18 ]
14 ]
[
(Fig . M) .
[
12 ]
to the desired position .
clockwise
14 ]
[
and check the
12 ]
[
. Risk of
[
12 ]
(Fig . A) .
[
7 ]
Attaching the handle
Fig . B
Fasten the handle
[
8 ]
To do so, use the following fastening materials:
–
Handle fixing screws
1 ]
[
–
Handle spring washers
[
2 ]
–
Flat washers (handle)
[
3 ]
Turn the handle fixing screws
until fully tightened .
Attaching the baseplate to the tripod
Fig . C to G
Fig.
Description
Place the baseplate
spotlights
and handle
9 ]
[
open mounting clamp
The handle
[
8 ]
direction of the retaining plate
mounting clamp
C,
Place the holes on the underside of the
D
baseplate
7 ]
[
clamp
.
11 ]
[
E
Close the retaining plate
mounting clamp
F
Fold the bracket of the mounting
clamp
upwards so that it grips the
11 ]
[
retaining plate
G
Press down the locking handle of
the mounting clamp
baseplate
.
[
7 ]
Attaching the spotlights to the baseplate
Fig . H
Secure the spotlight brackets
baseplate
.
7 ]
[
To do so, use the following fastening materials:
–
Spotlight fixing screws
4 ]
[
–
Flat washers
5 ]
[
–
Spring washers
6 ]
[
Turn the spotlight fixing screws
until fully tightened .
to the baseplate
.
[
7 ]
clockwise
[
1 ]
with the
7 ]
[
onto the
[
8 ]
.
11 ]
[
must be aligned in the
on the
23 ]
[
.
11 ]
[
on the pins of the mounting
of the
23 ]
[
.
11 ]
[
.
23 ]
[
to fix the
[
11 ]
to the
22 ]
[
clockwise
[
4 ]
GB/IE/NI
9
Advertenties
Hoofdstukken
Inhoudsopgave
