Inhoudsopgave
Advertenties
CAUTION!
Never let the bar
(20)
come into contact with sand or soil as this
will lead to increased wear of the chain.
Work positions:
The Pole Pruner can be operated in 2 working positions (above / below).
To ensure a tidy cutting edge, thick branches should be cut in 2 steps
(Illustrations similar).
Saw above (thick branches) [ Fig. O6 /O7 /O8 ]:
1. Saw the branch from below max. 1/3 of the diameter (the chain slides
to the front stop
(a)
).
2. Saw off the branch from above (the chain pulls to the rear stop
Saw below [ Fig. O6 /O9 ]:
v Saw off the branch from above (the chain pulls to the rear stop
To tilt the motor unit [ Fig. O10 ]:
The motor unit
(1)
can be tilted in 15° increments from 60° to – 60°.
1. Keep both orange buttons
desired direction.
2. Release both orange buttons
To extend the telescopic tube [ Fig. O11 ]:
(2)
The telescopic tube
can be continuously extended by up to 50 cm.
1. Loosen the orange nut
(12)
2. Extend the telescopic tube
3. Tighten the orange nut
(12)
To start the pole pruner [ Fig. O1 /O12 /O13 /O14 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example do
not attach the start lever to the handle.
Verify that the following conditions are met before commencing
work:
– The tank has been filled with sufficient chain oil and the lubrica-
tion system has been checked (see 3. OPERATION).
– The chain is tensioned (see 4. MAINTENANCE).
To start:
The product is provided with a two-switch safety device (start lever
with starting lockout) to prevent the product from being turned on
by accident.
1. Put the battery
(B)
into the battery holder
(13)
2. Open the snap fit
of the protective cover and remove from the bar.
3. Hold the pole pruner with one hand on the insulated gripping surface
(2)
on the telescopic tube
4. Slide the starting lockout
The pole pruner starts and the battery charge status indication
displayed for 5 seconds.
5. Release the starting lockout
To stop:
1. Release the start lever
(16)
.
The pole pruner stops.
2. Slide the protective cover onto the bar and close it until the snap fit
engages.
3. Push the locking button
(A)
(D)
holder
.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the chain to stop, remove the battery and slide the
protective cover over the bar before you maintain the product.
14
GAR_14770-20.960.03_2024-11-14.indd 14
GAR_14770-20.960.03_2024-11-14.indd 14
(11)
(1)
pushed and tilt the motor unit
(11)
(1)
and let the motor unit
engage.
.
(2)
to the desired length.
again.
(D)
until it audibly engages.
and with the other hand on the handle
(15)
forward and pull the start lever
(16)
(15)
.
and remove the battery
(B)
from the battery
To clean the Pole Pruner:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
1. Clean the pole pruner with a damp cloth.
2. Clean the airflow slots with a soft brush (do not use a screwdriver).
3. Clean the bar with a brush, if necessary.
(b)
).
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the
(b)
).
battery charger always are clean and dry before you connect the battery
charger.
Do not use running water.
v Battery charger: Clean the contacts and the plastic parts with a soft
in the
and dry cloth.
v Battery: Occasionally clean the ventilation slots and the terminals
on the battery using a soft brush that is clean and dry.
To tension the chain [ Fig. M1 /M2 / M3 /M4 ]:
RISK OF BURN INJURIES!
A too tightly tensioned chain can lead to motor overload and damage,
whereas insufficient tensioning can cause the chain to jump off the rail.
A correctly tensioned chain offers the best cutting performance, opti-
mum battery life and a longer service life. Therefore, you should check
the tensioning regularly as the chain may expand when being used
(especially when the chain is new; following first installation, the tension-
ing of the chain must be checked after the chainsaw has been used for
a few minutes).
v However, do not tension the chain immediately after use but
wait until it has cooled down.
The hex wrench for the screws
(18)
cover
.
1. Loosen the two screws
2. Lift the chain
(19)
in the middle of the bar
The gap should be approx. 2 – 3 mm.
3. Turn the adjusting screw
Turn the adjusting screw
too high.
4. Retighten the two screws
5. Start the pole pruner for approx. 10 sec.
6. Check the chain tension again and adjust it if necessary.
(14)
.
5. STORAGE
.
(P)
is
To put into storage [ Fig. O12 ]:
The product must be stored away from children.
1. Slide the protective cover onto the bar and close it until the snap fit
engages.
2. Remove the battery.
3. Charge the battery.
(13)
4. Clean the pole pruner, the battery and the battery charger
(see 4. MAINTENANCE).
5. Store the pole pruner, the battery and the battery charger in a dry,
enclosed and frost-free place.
Disposal of the product:
(according to Directive 2012/19/EU / S.I. 2013 No. 3113)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
(17)
is situated inside the protective
(17)
(17)
(Do not unscrew the screws
!)
(20)
.
(24)
clockwise if the chain tension is too low.
(24)
counterclockwise if the chain tension is
(17)
.
(13)
14.11.24 12:57
14.11.24 12:57
Advertenties
Inhoudsopgave
