Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
1. APPLICATIONS
Sanicompact
®
is a special bowl equipped with a
pump shredder intended to evacuate sanitary
effluents from the WC and the handbasin
(depending on the model).
2. INSTALLATION
• The fitting and working of your appliance must
meet local regulations and the EN 12056-4 standard.
• The bowl must be installed less than 3 cm from
a wall.
In order to optimise the technical developments in
acoustics included with this device, it is important to:
• install the bowl ensuring that it does not touch a
wall of the room,
• fix the outlet piping correctly avoiding any
distances between attachments in excess of one
metre.
Connecting to the water supply
The quality of the rinsing of the bowl depends on
the water pressure. For optimum rinsing, the outlet
dynamic pressure of your tap must be at least 1.7 bar
(0.17 MPa) and maximum 10 bar (1 MPa).
In the regions where the
water of the network is
dirty or sandy, we recommend inserting an
additional filter between the stop valve and the
device, in order to prevent complicated
maintenance work should be solenoid valve
become clogged.
Electrical connection
Do not connect the unit to a conventional plug and
socket. It must be wired into a fused, unswitched,
fixed wiring connector fitted with a 5 amp fuse.
GB Specification
The unit requires a 220-
240 V single phase AC 50 Hz supply.
Ensure the electricity is
turned OFF at the main
switch board before wiring to connector.
The wires in the mains lead are coloured in
accordance with the following code: Brown=Line,
Blue=Neutral, Green/Yellow=Earth.
3. COMMISSIONING
• Plug in the device.
• Fully open the water inlet in order to rinse
properly.
• Start the normal cycle by pressing the dark grey
part. Throw a few pieces of toilet paper in the bowl
and repeat the flush cycle.
• Handbasin option: let the tap of the handbasin
run, the device should start automatically. Check
that the connections do not leak.
4. USE
Never use the appliance
during a power failure.
Sanicompact
is controlled by an electronic
®
programmer. The operating life of your
Sanicompact
varies according to the cycle chosen:
®
- Eco cycle (light grey button),
- Normal cycle (dark grey button).
If necessary, you have the option of extending the
rinsing duration if the default setting is not sufficient
(low supply pressure).
Modifying the programme:
• Press and hold a button for more than 5 seconds.
The motor runs briefly twice: indicating that you
have entered programming mode.
• A press on the dark grey button or a long press on
the light grey button increases the duration of the
rinse cycle by 2 seconds. Each press is confirmed by
the motor running briefly.
• A short press on the light grey button reduces the
duration of the rinse cycle by 2 seconds. Each press is
confirmed by the motor running briefly.
• To exit programming mode: take no action for 7
seconds. The motor runs briefly twice indicating that
you have exited programming mode.
7. FAULT FINDING / REMEDIES
SYMPTOMS
After pressing the flush button
The electrical power supply is not active.
(24), the cycle does not start up.
The electrical power supply is defective.
The motor or the control system is defective.
The cycle starts but only a small
The inlet filter of the solenoid valve (28) is
amount of water drains from
clogged.
the bowl.
Input water flow is insufficient.
The cycle starts but the water does
Your stop valve is closed.
not drain from the bowl.
The solenoid valve (28) is fault.
The cycle runs normally, the motor
Input water flow is insufficient.
runs but the water in the bowl is
The U-bend valve (23) leaks.
drawn in slowly or not at all.
The cycle runs normally, but a lot
The outlet height is too great.
of water remains in the bowl.
The non-return valve leaks.
The motor runs with a rattling
Motor blocked by a foreign body.
noise or buzzes and does not run.
Problem with the motor or control system.
The device works intermittently.
The connected sanitary devices leak.
The non-return valve leaks.
Odours come from the U-bend of
The U-bend of the hand washer is empty.
the hand washer.
The water of the hand washer
Clogged hand washer U-bend.
does not drain automatically.
Problem with the automatic control system.
8. STANDARDS
This appliance conforms to EN 12050-3 and the
European standards concerning electrical safety and
electromagnetic compatibility.
DoP (Declaration of Performance) available on our
website in the product file.
9. DISPOSAL
The device must not be disposed of as
household waste and must be disposed
of at a recycling point for electrical
equipment. The device's materials and
components are reusable. The disposal
of electrical and electronic waste, recycling and
recovery of any form of used appliances contribute
to the preservation of our environment.
13
Note: the modified cycle remains in the memory
even after a power failure.
Hand basin operation (according to model)
Start-up takes place automatically. Ensure you check
that your Sanicompact
after use and does not leak.
6. MAINTENANCE
cut off the general water supply and to protect
the installation against frost.
Care of your unit
In order to remove scale and clean the macerator
and the bowl, use a household descalent (like Saniflo
Descaler).
IN ALL CASES, YOU MUST DISCONNECT
THE UNIT FROM THE POWER SUPPLY.
PROBABLE CAUSES
10. WARRANTY
The device is guaranteed for two years from the
date of purchase subject to installation, use and
maintenance in accordance with this manual.
water are covered by this warranty. Any damage
caused to the appliance by the shredding of foreign
bodies such as cotton, tampons, sanitary pads,
wipes, foodstuffs, condoms, hair, objects made of
metal, wood or plastic, or the pumping of liquids
such as solvents, oils or acids are not covered by the
warranty.
EN
®
connected basin is closed
In case of prolonged
absence, it is imperative to
REMEDIES
Restore the electrical supply.
Check the electrical power supply.
Ask an approved repair agent to
intervene.
Clean the filter of the solenoid valve.
• Increase the rinsing time
(programming).
• Modify the installation.
Open your stop valve.
Contact SFA customer services.
Clean or replace the U-bend valve (23).
Modify the installation.
The non-return valve leaks.
Remove the foreign body.
Consult an approved engineer.
Check the upstream installation.
lean or replace the anti-return valve.
Install a vacuum breaker.
Clean the U-bend.
Consult an approved engineer.
Only the evacuation of toilet
paper, faeces and sanitary
Advertenties
Inhoudsopgave
