Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
D - USE
Safety precautions:
Do not use the device within 20 cm of a wall or
similar surface, or any combustible object.
GB
Place the device on a sturdy, flat and horizontal
surface such a table but never on the ground. Never
move it while it is in operation.
In the event of a leak (smell of gas), close all valves.
Wait for the device to cool down completely before
handling it to return it to its place of storage.
After use, always close the valve on the regulator or
gas cylinder.
Stove: never use receptacles with a base diameter
less than 14 cm or greater than 24 cm. Do not use
utensils with a concave or convex base.
We recommend that you use gloves when handling
particularly hot components.
Ports sealed by the manufacturer or his agent must
not be altered by the user.
The stove and oven functions can be used simultaneously.
Stopgaz system
Your device is equipped with the STOPGAZ system
(depending on countries for the stove). This security system
allows the gas flow to be shut off when the burner flame is
accidently blown away (wind...).
–
The oven is equipped with this system (all countries).
–
The stove burners are also equipped with this system in
Germany and Austria.
1) STOVE FUNCTION
Electronic lighting of a stove burner with STOPGAZ
system (Germany and Austria)
–
Open the stove lid (1).
–
Open the gas supply (valve or lever on regulator).
–
Push
an
adjustment
9) and turn it anti-clockwise to the full flow
position (
). Keep pushing down the button 15
seconds maximum.
–
If the burner does not ignite after 15 seconds, release
the control knob and turn it clockwise to position
"off" (
). Wait at least 1 minute before repeating the
lighting operation.
–
When the burner is on keep pushing down the button
knob during 10 seconds then release it.
–
Adjust the flame to match the base of the pan being
heated by turning the control knob through the range
between (
) and ( ).
Manual lighting of a stove burner with STOPGAZ system
(Germany and Austria)
if igniter fails to light the stove, use a match to light burner.
Strike a match and bring it close to the burner. Push an
adjustment button down and turn it anti-clockwise until it is
in the full flow position (
When the burner is on keep pushing down the button knob
during 10 seconds then release it. Adjust the flame by turning
the control knob through the range between (
button
down
(see
)
) and ( ).
Electronic lighting of a stove burner without STOPGAZ
system (other countries)
–
Open the stove lid (1).
–
Open the gas supply (valve or lever on regulator).
–
Push an adjustment button down (see fig. 9) and turn
it anti-clockwise to the full flow position (
pushing the button 5 seconds until the burner lights.
Repeat 4 or 5 times if necessary.
–
If the burner does not ignite after 4 or 5 attempts, wait 5
minutes and then repeat the operation.
–
Adjust the flame to match the base of the pan being
heated by turning the control knob through the range
between (
Manual lighting of a stove burner without STOPGAZ
system (other countries)
if igniter fails to light the stove, use a match to light burner.
Strike a match and bring it close to the burner. Push an
adjustment button down and turn it anti-clockwise until it is
in the full flow position (
Adjust the flame to match the base of the pan being heated
by turning the control knob through the range between
(
) and (
).
Shutting down
–
Turn the knob of the appropriate burner clockwise to the
"off" position (
–
Close the valve on the regulator or gas cylinder if
necessary.
2) OVEN FUNCTION
Important:
Oven door must be opened during lighting.
It may be dangerous to open the oven door when the
cooking chamber is hot.
The load to place in the cooking chamber should be
7 kg maximum.
Lighting up the oven burner
–
Open the oven door.
fig.
–
Open the gas supply (valve or lever on regulator).
–
Push
the
oven
fig. 9) and turn it anti-clockwise to the full flow
position (
).
–
If the burner does not ignite after 15 seconds, release
the control knob and turn it clockwise to position
"off" (
). Wait at least 1 minute before repeating the
lighting operation.
–
When the burner is on (watch the flame through the
hole of the heat diffuser (6) (see fig. 9 - A)) keep pushing
down the button knob during 10 seconds then release it.
18
) and ( ).
).
).
adjustment
button
). Keep
down
(see
Advertenties
Inhoudsopgave
