Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
10.4
USER MENU
By once pressing P3 key you can hace access to user parameter controlling. To let them slide press P5 and P6
keys. They are:
POS.
REFERENCE
1
SET CLOCK
2
SET CHRONO
SELECT
3
LANGUAGE
4
STAND-BY MODE
BUZZER MODE
5
(audio alarm)
6
INITIAL LOAD
7
STOVE STATE
8
TECHNICA SETTING Only for the Authorized Technician.
9
SET FLAME
10.5
START UP
We remind you that the first ignition must be carried out by a specialized and authorixed technician who will
check that all is installed in compliance with current regulations and checks the efficiency.
• If inside the combustion chamber there are booklets, manuals, etc..., remove them.
• Check if the door is correctly closed.
• Check if the stove is correctly inserted in the electric socket.
• Before switching the stove on, assure you the burning pot is clean.
• To start the stove up, keep pressed P4 key for an instant till it will be shown "START" and "PREHEATI WAIT": the
preheating of the ingnition resistance starts. After 2 minutes about, it will be shown "PELLET LOAD, FLAME WAIT",
in this phase the auger loads the pellet and the heating of the resistance continues. When the temperature is
sufficiently high (after 7-10 minutes about), the ignition is considered as happened and on the display shows
"FIRE PRESENT".
• Completed the phase "FIRE PRESENT", the control unit enter the "WORK" phase showing the set calorific
power and ambient temperature. It is in this phase that P5 and P6 keys settle the stove power from 1 to 5. If
the value of the ambient temperature exceeds the limit set on the keyboard on the temperature setting, the
calorific power will be carried at the minimum showing "WORK, MODULATI". When the ambient temperature
turns back below the set temperatur, the stove turns back to the set power.
10.6
STOVE ADJUSTMENT
The stove is adjusted according to the chimney flue and used pellets datas, as per technical characteristics (see
FEATURES page 36). If the datas do not correspond, the authorized technician can adjust the stove.
• If the pellet is small in size and with a greater calorific power, (for example: encrusted burning pot), the pellet
drop must be decreased from the menu "SET FLAME", press P3 "PELLET TYPE", press P3 again "PELLET LOAD"
and with P2 key decrease the pellet quantity from -1 (which is -2%) till -9 (which is -18%).
• If the chimney flue has a lower draught (for example: weak flame, sooty glass) the revolutions of the geared
NICE - MIRIAM - CRISTAL - LEONORA - PRETTY - DIANA - KRISS - MARY
DESCRIPTION
Set date and time. The board is provided with a lithium battery which enables a clock
autonomy of 3/5 years. See CLOCK SETTING page 21.
Press once P3: "CHRONO ENABLE" appears. Press P3 again and with P1 and P2 put in
"OFF" or "ON". For daily, week-end or weekly programming, see DAILY PROGRAMMING
page 21. CAUTION: do not active if STAND-BY function is active!
Press once P3 key and with P1 and P2 keys select the desired language.
It activates a function which, if the set ambient temperature has been exceeded for
more then 10 minutes, start the switching off phase up. If the ambient temperature has
fall at more than 2°C, the stove will restart automatically up, starting from START UP page
19. Press once P3 key and with P1 and P2 keys put in "OFF" or "ON". CAUTION: do not
activate if CHRONO function is active!
Press once P3 key and with P1 and P2 keys put in "OFF" or "ON".
When the stove has its first ignition, the auger is completely empty. If it should be necessary
do a precharge by pressing P3 key, then P1 key for starting up and P4 key for stop.
It shows all parameters connected to the stove state: this is a menu for the Authorized
Techinician
It enables to set the flame dipending on the draught of the chimney flue.
EN
19
Advertenties
Hoofdstukken
Inhoudsopgave
