Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Caution
Never operate the machine if the safety and monitor-
ing devices have been removed or damage, or if they
do not work.
2.8. Pumped fluids
Each pumped fluid differs in regard to composition, cor-
rosiveness, abrasiveness, TS content and many other
aspects. Generally, our products can be used for many
applications. For more precise details, see chapter 3, the
machine data sheet and the order confirmation. It should
be remembered that if the density, viscosity or the gener-
al composition change, this can also alter many parame-
ters of the product.
Different materials and impeller shapes are required for
different pumped fluids. The more exact your specifica-
tions on your order, the more exactly we can modify our
product to meet your requirements. If the area of applica-
tion and/or the pumped fluid change, we will be happy to
offer supportive advice.
When switching the product into another pumped fluid,
observe the following points:
•
Products which have been operated in sewage or
waste water must be thoroughly cleaned with pure
water or drinking water before use.
•
Products which have pumped fluids which are haz-
ardous to health must always be decontaminated
before changing to a new fluid. Also clarify whether
the product may be used in a different pumped fluid.
•
With products which have been operated with a lu-
bricant or cooling fluid (such as oil), this can escape
into the pumped fluid if the mechanical shaft seal is
defective.
Danger - explosive fluids!
It is absolutely prohibited to pump explosive liquids
(e.g. gasoline, kerosene, etc.). The products are not
designed for these liquids!
2.9. Sound Pressure
Depending on the size and power (kW), the pump has
a sound pressure of about 40dB (A) to 70dB (A) during
operation. However, the actual sound pressure depends
on several factors. These are, for example, the type of
installation and set-up, mounting of accessories, piping,
operating point, immersion depth, and much more.
3. General Description
3.1. Utilization
Saniboy G and Sanimaster G wastewater disposal sys-
tems are utilized for building drainage below the back-
wash level in accordance with DIN EN 12506. The com-
pact design allows space-saving installation and simple
installation as well as retrofitting. With chemically aggres-
sive components in the pumped medium the resistance
of the pumps used and container materials must be noted
without fail.
The pH value of the promoting medium may fall between
5 and 11.
3.2. Type of application
The wastewater lifting unit is designed for 40% S3
intermittent operation.
3.3. Structure
The plastic connection container has the following
connections:
•
Vertical inlet pipes DN100 / DN40
•
Horizontal inlet pipes DN100 / DN40
•
Vent pipes DN 70
•
Cleaning opening
•
Pneumatic control connection
•
Manual diaphragm pump connection
The pump has a cutting unit upstream from the impeller.
It consists of a permanently attached stainless steel cut-
ting ring and a rotating stainless steel cutting head and
crushed entrained solids so that the fluid can be pumped
through small pipe diameters (from DN 50).
The technical specifications are as follows:
Technical Data
Power consumption
Motor power
Voltage
Speed
Nominal current
Pump protection system
Control unit protection system IP 54
System weight
Saniboy G / Sanimaster G
Permitted medium temperature 35°C
Pressure connection
Container volumes
Switching volumes
Saniboy G / Sanimaster G
180 -16W
180-16D
180-26D
250 -16W
250-16D
250-26D
1.5 kW
1.3 kW
2.5 kW
1.1 kW
0.9 kW
1.9 kW
230V / 1Ph 400V / 3Ph
2900 rpm
7.5 A
2.5 A
4.4 A
IP 68
37 / 62 kg 37 / 62 kg
51 / 89 kg
BSP 1½"F
46 l
31 l
EngliSH | 25
Advertenties
Hoofdstukken
Inhoudsopgave
