Inhoudsopgave
Advertenties
1. Appearance (Page 1 – A)
No.
Component
Interface
1
Cover
2
Microphone
Charging
3
Indicator
4
Loudspeaker
Touch
5
Screen
Power
6
Button
Shutter
7
Button
8
File
9
Back Button
10
Navigation
Button
11
Laser Button
12
Battery
Laser
13
Distance
Meter
14
Optical Lens
15
LED Light
Thermal
16
Lens
17
Focus Ring
Tripod
18
Interface
Hand Strap
19
Buckle
Interface
20
Focus
English
Function
Protect the interfaces from
dust.
Input audio information.
Red: Charging
Green: Fully charged
Play voice note, voice alarm,
and video voice.
Touch the screen to set
parameters.
Hold: Power on/off
Press: Perform image
correction with a shutter click
in the camera.
Inspection Route Mode:
Press the button to view
the information of
inspection points.
Non-Inspection Route
Mode: Press the button
to view the capture and
video.
Exit the menu or return to
previous menu.
Menu Mode:
Press , , , and to
select parameters.
Press OK to confirm.
Press to enter the
submenu.
Press to return to the
previous menu.
Non-Menu Mode:
Press to turn on/off
the
LED
supplement.
Press to start digital
zoom.
Hold the button to turn on
laser, and release the button
to turn off laser.
Provide power for the device.
Measure the distance with
laser.
View the optical image.
Increase ambient brightness
in dark environment.
View the thermal image.
Adjust the lens position at the
optical axis of the thermal
lens.
Install the tripod.
Insert the screw to fix the
hand strap buckle.
Pull the trigger to enable laser
No.
Component
Trigger
21
Main Trigger
Hand Strap
22
Hole
Memory
23
Card Slot
Type-C
24
Interface
CVBS
25
Interface
Reserved
26
Card Slot
Micro HDMI
27
Interface
Note:
The warning sign is under the laser and on the
left of the device.
The interfaces may vary according to different
models. Please refer to the actual products.
Initialize the memory card before first use of it.
Please refer to the product specification for
details about the device accessories.
2. Charge Device via Charging Base
(Page 1 – B)
After the device starts up, the OSD (on-screen
display) shows the battery status. When the battery
is low, charge the device and ensure it works
properly.
light
For the first charge, charge the device for 10 hours
when the device is turned on.
The power delivered by the charger must be between
min 10 Watts required by the radio equipment, and
max 10 Watts in order to achieve the maximum
charging speed.
Note：
The built-in cell battery that powers the real
time clock (RTC) of the device may drain during
longtime transportation or storage. It is
recommended to recharge the RTC battery for
the wellfunctioning of the device clock.
To fully charge the RTC battery, the following
requirements should be met:
a)
The rechargeable lithium batteries should
be installed on the device.
b)
The device should keep working for more
than 10 hours before shutting down.
Steps:
1. Hold the device, and press both battery lock
catches of the device.
2. Hold the lock catches, and draw the battery base
to take out the battery.
3. Insert the battery into the charging base. You
can see the charging status via the pilot lamp on
the charging base.
4. When the battery is fully charged, draw the
battery from the charging base.
3
Function
assisted focus/auto focus
function.
Pull the trigger to capture
or scan the QR code.
Hold the trigger to record
videos.
Thread the lower part of the
hand strap through the hole.
Insert the memory card.
Connect to power supply and
transmit data.
Connect the device and
display unit to view the image
for details.
Insert the reserved card.
Connect the device and
display unit with Micro HDMI
(type D) to HDMI (type A)
cable to view the image for
details.
Advertenties
Inhoudsopgave
