Download Inhoudsopgave Inhoud Print deze pagina

Unblocking The Collector Channel; End Of Mowing; End Of Work; Cleaning The Machine - GGP MJ 66 Gebruikershandleiding

Inhoudsopgave

Advertenties

WARNING!
When cutting on sloping
ground, the forward speed must be re-
duced to ensure safe conditions (see 1A-
C7-8-9).
Whatever the conditions, always reduce the 
speed if you notice a drop in engine speed – if 
you travel too fast compared to the amount of 
grass being cut, you will not be able to mow the 
grass well.
Disengage the cutting means and raise the 
cutting-means assembly as high as possible 
whenever you need to get past an obstacle.
5.4.6 Emptying the grass catcher
(Fig. 5.10)
NOTE The emptying of the grass catcher can
only be done with the cutting means disengaged,
otherwise the engine stops.
The grass catcher is full when the grass cuttings 
remain on the lawn. If you continue mowing with 
the grass catcher full, it may block the collector 
channel.
To empty the grass catcher:
–  disengage the cutting means (see 4.3);
–  lower the engine speed;
–    s hift into neutral (N)  (see  4.12 – Mechanical 
transmission or 4.22 – Hydrostatic transmis-
sion) and stop moving forward;
–  engage the parking brake on slopes;
–    h old onto the rear handle (1) and tip up the 
grass catcher to empty it;

5.4.7 Unblocking the collector channel

Cutting very tall or wet grass, particularly at ex-
cessively high speed, can clog up the collector 
channel. If this happens proceed as follows:
–    s top forward movement immediately, disen-
gage the cutting means and stop the engine;
–    r emove the grass catcher;
–    r emove the grass cuttings; you can reach 
them from the channel discharge opening.
WARNING!
This job must only be per-
formed with the engine turned off.

5.4.8 End of mowing

When you have finished mowing, disengage the 
cutting means, reduce the engine speed and 
ride the machine with the cutting-means assem-
bly in the highest position.
All manuals and user guides at all-guides.com
Stop the machine, put the accelerator lever in 
the «SLOW» position and turn off the engine by 
putting the ignition key into the «OFF» position.
When the engine has stopped, close the fuel 
stopcock (1) (if fitted). Fig. 5.11)
accelerator in the «SLOW» position for 20
seconds before stopping the engine.
do not leave the ignition key in the «ON» position
when the engine is not running.
After each mowing session, clean the outside 
of the machine, empty the grass catcher and 
shake it to remove residual grass and earth.
Clean the plastic parts of the body with a damp 
sponge using water and detergent, taking care 
not to wet the engine, the electrical parts or the 
electronic circuit board located under the seat.
harsh detergents for cleaning the body and en-
gine!
grass accumulate in the upper part of the
cutting-means assembly in order to maintain
maximum machine efficiency and safety
levels.
After each use, clean the cutting-means as-
sembly thoroughly to remove any grass remains 
or debris.
keep people or animals away from the sur-
rounding area when cleaning the cutting-
means assembly.
a)  When washing the inside of the cutting-
means assembly and the collector channel, the 
machine must be on firm ground:
–    p repare the machine according to the operat-
–    c onnect a water hose to its pipe fitting (1), and 
–  sit in the operator's position;
–    l ower the cutting-means assembly com-
–  start the engine and stay in neutral;
–    e ngage the cutting means and allow them to 
12

5.4.9 End of work

WARNING!
To avoid backfire, put the
IMPORTANT To keep the battery charged,

5.4.10 Cleaning the machine

IMPORTANT Never use hose-nozzles or
WARNING!
Do not let debris and dried
WARNING!
Wear eye protection and
ing mode that was used the last time (see 
5.3.4);
run water through it (Fig. 5.12);
pletely;
run idle for a few minutes.

Advertenties

Inhoudsopgave
loading

Inhoudsopgave