Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
9.2.1 Connection to an external dust extractor
• Attach the extraction hose of a workshop vacuum cleaner to
the extraction port (17a).
• The workshop vacuum cleaner must be suitable for the mate-
rial being worked.
Attention! Always observe the safety and warning notices of
the workshop vacuum cleaner being used.
• When vacuuming dust that is especially detrimental to health
or carcinogenic, use a special vacuum cleaner.
9.3 Precision adjustment of the stop for crosscut
90° (fig. 1/6/7)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (23).
• Loosen the set screw (22).
• Position the angle stop (A) between the saw blade (6) and
the rotary table (14).
• Loosen the lock nut (26a).
• Adjust the adjusting screw (26) until the angle between the
saw blade (6) and rotary table (14) is 90°.
• Re-tighten the lock nut (26a).
• Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (19) using a Philips screwdriv-
er, set to position 0° on the angle scale (18) and re-tighten
the retaining screw.
9.4 Precision adjustment of the stop for mitre cut
45° (fig. 1, 7-11)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (23).
• Fix the rotary table (14) in the 0° position.
Attention! For mitre cuts (inclined saw head), the moveable
stop rail (16a) must be fixed in the outer position (left side).
• Open the set screw (16b) for the moveable stop rails (16a)
and push the moveable stop rails (16a) outwards.
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is no more than 8 mm.
• The moveable stop rail (28) must be fixed in the inner posi-
tion (right side).
• Before making the cut, check that no collision can occur be-
tween the stop rails (16a) and the saw blade (6).
• Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade (6) and
rotary table (14).
• Loosen the lock nut (27a) and adjust the adjustment screw
(27) until the angle between the saw blade (6) and the ro-
tary table (14) is precisely 45°.
• Re-tighten the lock nut (27a).
• Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (19) using a Philips screwdriv-
er, set to position 45° on the angle scale (18) and re-tighten
the retaining screw.
10. Operation
10.1 Using the laser / LED (fig. 12)
Function
OFF
10.2 Changing the speed (fig. 12)
The mitre saw has 2 speed ranges:
• To operate the mitre saw at a speed of 3200 rpm (metal), set
the speed regulation switch (34) to position I.
• To operate the saw at a speed of 5000 rpm (wood), set the
speed regulation switch (34) to position II.
10.3 Limiting the cutting depth (cutting grooves)
(fig. 13)
m WARNING
Risk of kickback! When cutting grooves, it is
particularly important that no lateral pressure is
exerted on the saw blade. Otherwise, the saw
head might suddenly kick back! Use a clamping
device when cutting grooves. Avoid lateral pres-
sure on the saw head.
• The cutting depth can be infinitely adjusted using the screw
(24). To do this, loosen the knurled nut (24a) on the screw
(24). Turn the screw (24) in or out to set the required cutting
depth. Then re-tighten the knurled nut (24a) on the screw
(24).
• Check the setting by completing a test cut.
10.4 Crosscut 90° and turntable 0° (fig. 1/2/8)
In the case of cutting widths up to approx. 100 mm it is possible
to fix the traction function of the saw with the set screw (20) in
the rear position. In this position the machine can be operated
in cross cutting mode. If the cutting width is over 100 mm then
it is necessary to ensure that the set screw (20) is loose and the
machine head (4) can move.
Attention! For 90° crosscuts, the moveable stop rail (16a)
must be fixed in the inner position.
• Open the set screw (16b) for the moveable stop rails (16a)
and push the moveable stop rails (16a) inwards.
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is no more than 8 mm.
Press the ON/OFF switch
laser/LED (33)
1x
1x
1x.
1x
GB/IE/NI
9
Advertenties
Hoofdstukken
Inhoudsopgave
