Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
23 Replace table inserts when worn!
24 Avoid overheating of the saw teeth.
25 When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose. Replace
damaged or worn saw blades immediately.
When the saw blade overheats, stop the machine. Allow
the saw blade to cool down before using the machine
again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unprotected
eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces and
persons or animals. Even a laser beam with a low output
can cause damage to the eyes.
• Caution - methods other than those specified here can result
in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure to the
beam can occur.
• The laser may not be replaced with a different type of laser.
• Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
• Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
• Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instructions"
and the „Proper use" are observed along with the whole of
the operating instructions.
• Do not load the machine unnecessarily: excessive pressure
when sawing will quickly damage the saw blade, which re-
sults in reduced output of the machine in the processing and
in cut precision.
• When cutting plastic material, please always use clamps:
the parts which should be cut must always be fixed between
the clamps.
• Avoid accidental starting of the machine: the operating but-
ton may not be pressed when inserting the plug in an outlet.
• Use the tool that is recommended in this manual. In doing so,
your machine provides optimal performance.
• Hands may never enter the processing zone when the ma-
chine is in operation.
• Release the handle button and switch off the machine prior
to any operations.
Warning! This electric tool generates an electromagnetic field
during operation. This field can impair active or passive medical
implants under certain conditions. In order to prevent the risk of
serious or deadly injuries, we recommend that persons with medi-
cal implants consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
7. Technical data
AC motor....................................................220 - 240 V ~ 50 Hz
Power S1* ..................................................................2000 Watt
Idle speed n
0
1
gear ........................................................................ 3200 min
st
2
gear ....................................................................... 4500 min
nd
Carbide saw blade ...............................ø 255 x ø 30 x 2,2 mm
Number of teeth .......................................................................48
Maximum tooth width of saw blade .................................. 3 mm
Swivel range .................................................. -45° / 0°/ +45°
Mitre cut ....................................................0° bis 45° to the left
Saw width at 90° ................................................. 340 x 90 mm
Saw width at 45° ................................................. 240 x 90 mm
Saw width at 2 x 45°
(double mitre cut) .................................................. 240 x 45 mm
Protection class .................................................................... II /
Weight ....................................................................... ca. 14,7 kg
Laser class ................................................................................... 2
Wavelength of laser ........................................................ 650 nm
Laser output .....................................................................< 1 mW
* S1 operating mode, continuous duty
The work piece must have a minimum height of 3
mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Noise
Total noise values determined in accordance with EN 62841.
Sound pressure level L
............................................ 97,2 dB(A)
pA
Uncertainty K
......................................................................3 dB
pA
Sound power level L
............................................110,2 dB(A)
WA
Uncertainty K
.....................................................................3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing
The above-mentioned noise emission values were measured in
accordance with a standardised test procedure and can be
used to compare one power tool with another.
The above-mentioned noise emission values can also be used
for the preliminary assessment of exposure.
Warning:
• The noise emissions during the actual use of the power tool
may differ from the above-mentioned values depending on
the power tool being used, in particular on the type of work-
piece being processed.
• Try to keep emissions as low as possible. For example: Limit
your working time. In this regard, all the operational cycle
phases must be taken into consideration (such as the times
when the tool is switched off or running idle).
-1
-1
GB/IE/NI
7
Advertenties
Hoofdstukken
Inhoudsopgave
