Inhoudsopgave
Advertenties
GB/IE/NI
tion. Continuous operation via the mains power
adapter
3
is possible.
6.2 Charging via solar panel
The solar panel
4
is firmly attached at the top of the
lampshade. The lamp can be charged by means of
the integrated
4
solar panel.
NOTE!
The charging time using solar panels
4
depends on
the intensity of solar radiation.
Charging by solar panel is intended as a supportive
charging option for outdoor areas in order to pro-
long the lighting duration. Full charging of the bat-
tery can only take place via the mains power adapt-
er
3
indoors.
6.3 Structure of the lamp (B)
Type 351862-20-A
1. Screw-connect the metal base
1c
and the three
metal posts
1b
as shown.
2. Lastly screw-connect the lampshade
1a
with the
upper metal post 1b.
Type 351862-20-B
1. Screw 3 poles
2c
into the pole cross 2b. Screw
the 3 additional poles
2c
into the previously
screwed-in poles.
2. Screw-connect the 3 poles with a plastic foot
into the previously screw-connected poles.
3. Lastly, screw-connect the lampshade
2a
onto the
upper metal post 2b.
6.4 Outdoor use (B)
Type 351862-20-B only
When using the product outdoors (e.g. in the gar-
den), attach the 3 supplied ground spikes
6
to the
poles with plastic base
2d
of the product, see Fig. B.
The product can thus be fixed in the ground.
NOTE!
Please make sure to remove the ground spikes
when using them indoors to avoid damage to sen-
sitive floors.
7. Operation
7.1 Operation on the lampshade (C1)
7.1.1 Switching the lamp on/off
- Press and hold the HOLD (2s): ON / OFF -
CLICK: Press and hold the DIM & COLOR button
10, hereinafter referred to as button 10, for ap-
10
prox. 2 seconds to turn on the lamp.
- Press and hold the
10
button for approx. 2 sec-
onds to turn off the lamp.
7.1.2 Modes
When the lamp is switched on, you can use the but-
ton
to switch through the individual modes by
10
pressing 1x at a time as follows:
- warm white brightness level I
- warm white brightness level II
- warm white brightness level III
- automatic colour change
- red
- green
- blue
- yellow
- orange
- pink
- purple
7.1.3 Sensor OFF-/ON-Modi
With the SENSOR ON-/OFF button 11, you can
switch between the following modes.
- Sensor ON: The lamp switches on automatical-
ly in darkness and switches off automatically in
bright light.
The last active color is saved and changes to the
lowest brightness (memory effect).
- Sensor OFF: The lamp must be switched on and
2d
off manually.
NOTE!
7.2 Operation with the infrared remote
control
7.2.1 Activating the infrared remote con-
trol (C2)
The infrared remote control battery
5
against discharging with a film (c) when delivered.
Pull it out as shown before using it for the first time.
The infrared remote control
is now ready for use.
5
7.2.2 Switching options with the infrared
6
remote control (C3)
ON = switch on the lamp
OFF = switch off the lamp, the last active color and
brightness are saved (memory effect).
PLAY/PAUSE = automatic colour change mode
COLOUR = colour selection (sequence, press 1x
each: red, green, blue, yellow, orange, pink, purple)
BRIGHT± = brightness levels (4) of the individual col-
ours (except for white)
CANDLE = flickering effect (similar to a burning candle)
SPEED = Change the speed of the colour change in
the automatic colour change mode
WHITE: Light level selection in warm white mode (se-
quence, press 1x each: Brightness level I, brightness
level II, brightness level III)
WARNING!
!
Due to the extremely fast speed of the light change,
sight impairments could occur under certain circum-
stances with children or people who have a disorder
(e.g. due to psychological disorders).
8. Replacing the infrared remote
control battery (D)
If your infrared remote control
it may be that the battery is empty and must be re-
placed.
To replace the infrared remote control
proceed as follows:
1. Push the battery compartment lock inward as
shown.
2. Pull out the battery compartment as shown, and
remove the depleted battery.
3. Insert a new battery into the battery compartment
as shown.
NOTE!
Only use type CR2025 batteries. Make sure that the
polarity is correct when inserting a new battery. (For
information on how to dispose of used batteries, see
Chapter "14. Disposal".)
4. Push the battery compartment back into the infra-
red remote control
place. Your infrared remote control
is protected
ready for use again.
9. Replacement of the lamp bat-
tery (E)
A longlife battery
12
longer performs satisfactorily, you can replace it with
a lithium-ion battery 18650 of the same design.
NOTE!
- Observe the applicable national requirements
and regulations for the use and disposal of the
product.
- Do not use non-rechargeable batteries.
To replace the lamp battery, proceed as follows:
1. Open the battery compartment cover 13, by re-
moving the screws
driver.
2. Pull the rubber cover
partment 16.
3. Remove the depleted battery 12.
4. Insert a new battery of the same type into the bat-
tery compartment
Pay attention to the correct polarity.
5. Push the rubber cover
compartment 16.
no longer functions,
Make sure to push the rubber cover
5
into the groove, so that the battery compartment is
sealed. This is the only way to ensure protection from
battery,
splashing water.
5
6. Replace the battery compartment cover
battery compartment
14
one after the other.
7. Charge the battery as described under 6. Start-
up.
10. Storage
If you do not intend to use the product in the winter,
we recommend storing it. This way, the service life
will be extended of the installed rechargeable bat-
tery and battery.
1. Clean the product as described under "11. Clean-
ing and care instructions".
5
until you hear it click into
2. Remove the depleted batteries from the infrared
5
is now
remote control
3. If available, wrap the product in bubble wrap or
similar.
4. Store the product in a dry, warm place that is pro-
tected from UV light.
is installed in the lamp. If it no
5. Store the infrared remote control with the re-
moved battery in a place that is not accessible for
children.
11. Cleaning & care instructions
Risk of injury!
Switch the lamp off before cleaning.
Before cleaning, you must discon-
nect the mains adapter plug. There
is a risk of electric shock!
GB/IE/NI
14
with a crosshead screw-
15
off of the battery com-
16
as shown.
15
back onto the battery
NOTE!
carefully
15
13
on the
and screw in the screws
16
NOTE!
WARNING!
!
11
Advertenties
Inhoudsopgave
Probleemoplossen
