Hikmicro SP Series Snelstartgids pagina 17
Verberg thumbnails
Zie ook voor SP Series:
- Gebruiksaanwijzing (57 pagina's) ,
- Snelstartgids (64 pagina's)
Inhoudsopgave
Advertenties
● When the device is powered off and
the RTC battery is full, the time
settings can be kept for 3 months.
● In the first use, power on the device
and charge the RTC battery with the
lithium battery for more than
2 hours.
● The battery voltage is 7.2 V, and the
battery capacity is 4800 mAh.
● The battery is certified by UL2054.
Maintenance
● If the product does not work
properly, please contact your dealer
or the nearest service center. We
shall not assume any responsibility
for problems caused by
unauthorized repair or maintenance.
● A few device components (e.g.,
electrolytic capacitor) require
regular replacement. The average
lifespan varies, so periodic checking
is recommended. Contact your
dealer for details.
● Wipe the device gently with a clean
cloth and a small quantity of
ethanol, if necessary.
● Clean the lens with cotton wool and
99% ethyl alcohol.
● If the equipment is used in a manner
not specified by the manufacturer,
the protection provided by the
device may be impaired.
● We recommend you send the device
back for calibration once a year, and
please contact the local dealer for
the information on maintenance
points.
● Please notice that the current limit
of USB 3.0 PowerShare port may
vary with the PC brand, which is
likely to result in incompatibility
issue. Therefore it's advised to use
regular USB 3.0 or USB 2.0 port if the
USB device fails to be recognized by
PC via USB 3.0 PowerShare port.
●Your camera will periodically perform
a self-calibration to optimize image
quality and measurement accuracy.
In this process the image will pause
briefly and you'll hear a "click" as a
shutter moves in front of the
detector. The self-calibration will be
more frequent during start up or in
very cold or hot environments. This
is a normal part of operation to
ensure optimum performance for
your camera.
Using Environment
● DO NOT expose the device to
extremely hot, cold, dusty, corrosive,
saline-alkali, or damp environments.
Make sure the running environment
meets the requirement of the
device. The operating temperature
shall be -20 °C to 50 °C (-4 °F to
122 °F), and the operating humidity
shall be 95% or less.
● Place the device in a dry and well-
ventilated environment.
● DO NOT expose the device to high
electromagnetic radiation or dusty
environments.
● DO NOT aim the lens at the sun or
any other bright light.
● When any laser equipment is in use,
make sure that the device lens is not
exposed to the laser beam, or it may
burn out.
● The device is suitable for indoor and
outdoor uses, but do not expose it in
wet conditions.
● The level of protection is IP 54.
● The pollution degree is 2.
Technical Support
● The https://www.hikmicrotech.com
portal will help you as a HIKMICRO
customer to get the most out of
your HIKMICRO products. The portal
gives you access to our support
team, software and documentation,
service contacts, etc.
Emergency
● If smoke, odor, or noise arises from
the device, immediately turn off the
power, unplug the power cable, and
contact the service center.
Laser
inflammable substances. Prevent eyes
from direct laser. Before enabling the
Light Supplement function, make sure
no human or inflammable substances
are in front of the laser lens. The wave
length is 650 nm, and the power is less
than 1 Mw. The laser meets the
IEC60825-1:2014 standard.
Laser maintenance: It is not necessary
to maintain the laser regularly. If the
laser does not work, the laser
15
Warning: The laser
radiation emitted
from the device can
cause eye injuries,
burning of skin or
Advertenties
Inhoudsopgave
