Inhoudsopgave
Advertenties
en
|
Device settings
Designation and descrip-
tion
Inductive charging cradle for
charging 1 gas detector
Adapter for the plug-in power
supply unit
Plug-in power supply unit for
charging 1 gas detector
Plug-in power supply unit for
charging 5 gas detectors
Plug-in power supply unit
100-240 V AC; 1.33 A for
charging up to 5 gas detec-
tors
(requires adapter 83 25 736)
Plug-in power supply unit
100-240 V AC; 6.25 A for
charging up to 20 gas detec-
tors
(requires adapter 83 25 736)
Vehicle connection 12 V /
24 V for charging 1 gas
detector
Vehicle connection 12 V /
24 V for charging up to 5 gas
detectors
(requires adapter 83 25 736)
Vehicle mount
(requires adapter 83 25 736
and vehicle connection
83 21 855)
5.7
Cleaning
The gas detector does not require any special care.
If it is heavily soiled, wash the gas detector with cold water
and use a sponge if necessary. Dry the gas detector with a
cloth.
NOTICE
Damage to the gas detector!
Harsh cleaning utensils (e.g. brushes), detergents and
solvents can destroy the dust and water filters.
► Only clean the gas detector with cold water and, where
necessary, a sponge.
► If the gas inlets are protected by the pump adapter, then a
soft brush can also be used to clean the device. After
cleaning, make sure that the gas inlet is free.
The shoulder strap can be cleaned with water and without
cleaning agents in a wash bag in an (industrial) washing
machine.
For information on suitable cleaning agents and disin-
fectants and their specifications, see document
9100081 at www.draeger.com/IFU.
40
6
Order no.
Only trained and qualified personnel may change the device
83 25 825
settings.
For more details, refer to the technical manual.
83 25 736
6.1
83 16 997
Different settings can be selected to meet customer
requirements on order. The setting can be checked and
83 16 994
changed with the Dräger CC-Vision PC software.
83 21 849
gas detector once transmitted in order to ensure they were
transmitted correctly.
Parameters that are not visible on the gas detector must be
read out and checked for changes using the Dräger CC-
Vision PC software.
83 21 850
Function
Fresh air calibration without
password
Bump test without password
45 30 057
Life signal
Switch off allowed
83 21 855
Capture range
LEL factor
ch4 (methane)
H
83 27 636
STEL
TWA
Alarm threshold configuration ATEX compliant
Alarm A1
Alarm A2
Symbol for type of danger
Expired bump test interval
Expired calibration interval
Power-save mode display
1) The set capture range can be read out and selected or disabled at the
2) An LEL factor can be adapted to national regulations using the Dräger
Device settings
Factory settings
The changed parameter settings must be checked at the
1)
2)
(hydrogen)
2
gas detector. The capture range is activated in measuring mode at the
factory. The capture range is always disabled in calibration mode.
CC-Vision PC software.
Instructions for use
Setting
On
Off
On
On
On
4.4 Vol% (corresponds to
100 %LEL)
4.0 Vol% (corresponds to
100 %LEL)
STEL feature – inactive;
average duration =
15 minutes
TWA feature – inactive; aver-
age duration = 8 hours
Acknowledgeable, non-latch-
ing, pre-alarm, increasing
measured value (for O
sen-
2
sors, decreasing measured
value as well)
Non-acknowledgeable, latch-
ing, main alarm, increasing
measured value (for O
sen-
2
sors, decreasing measured
value as well)
On
Warning
Channel warning
Off
®
|
X-am
3500
Advertenties
Hoofdstukken
Inhoudsopgave
