Maintenance And Cleaning - Bosch GOF Professional 1250 CE Oorspronkelijke Gebruiksaanwijzing

Verberg thumbnails Zie ook voor GOF Professional 1250 CE:

pagina van 263

/ 263
Inhoud
Inhoudsopgave
Bladwijzers

Inhoudsopgave

Advertenties

Beschikbare talen

While it is switched on, guide the power tool towards the

workpiece from the side until the pilot pin or the ball bearing

of the router bit is touching the side of the workpiece edge

that you want to machine.

Guide the power tool along the workpiece edge. Pay atten-

tion that the router is positioned perpendicularly. Too much

pressure can damage the edge of the workpiece.

Routing with a parallel guide (see figure H)

Slide the parallel guide (33) with the guide rods (34) into

the base plate (13) and tighten it with the wing bolts (7) ac-

cording to the required dimension.

Additionally, the parallel guide can be adjusted lengthwise

with the wing bolts (36) and (35).

Fine adjustment of the length is possible with the adjustment

knob (37) after loosening both wing bolts (35). One revolu-

tion corresponds to an adjustment range of 2.0 mm. Each of

the graduation marks on the knob (37) changes the adjust-

ment range by 0.1 mm.

The effective contact surface of the parallel guide can be ad-

justed with the fence (38).

While it is switched on, guide the power tool along the work-

piece edge with a uniform feed and while applying lateral

pressure to the parallel guide.

When routing with the parallel guide (33), the dust/chip ex-

traction should take place via the special extraction

adapter (39). The extraction adapter can remain fitted.

Routing with the Circle Cutting Adapter (Accessory)

You can use the circle cutting adapter for circular routing

work.

Routing with the Guide Rail (Accessory)

You can use the guide rail and guide rail adapter to rout in

straight lines.

Routing with the guide bushing (see figures I–L)

Using the guide bushing (43), you can transfer contours

from templates or patterns to the workpiece.

Select the guide bushing that is suitable for the thickness of

the template or pattern. Due to the protruding height of the

guide bushing, the template must have a minimum thickness

of 8 mm.

In order to use the guide bushing (43), the SDS guide-bush-

ing adapter (40) must first be inserted into the guide

plate (11).

Place the guide-bushing adapter (40) from above onto the

guide plate (11) and tighten it firmly with the 2 fastening

screws (41). Ensure that the release lever for the guide-

bushing adapter (42) is freely movable.

Push the release lever (42) in the direction of the arrow and

insert the guide bushing (43) from below into the SDS

guide-bushing adapter (40). The coding cams must audibly

click into the recesses of the guide bushing (43).

Check the clearance from the router bit centre and guide-

bushing edge (see "Centring the Base Plate (see figure N)",

page 21).

Bosch Power Tools

Select a router bit with a diameter that is smaller than

the interior diameter of the guide bushing.

Routing Process

Switch the power tool on and move it with the guide

bushing (43) towards the template.

Push the release lever (23) backwards and slowly guide the

router down until the set routing depth has been reached.

Let go of the release lever (23) again in order to lock the

plunging depth.

Guide the power tool with the protruding guide bushing (43)

along the template using lateral pressure.

Centring the Base Plate (see figure N)

To ensure that the distance from the router bit centre to the

guide-bushing edge is uniform, the guide bushing (43) and

the guide plate (11) can be adjusted to each other, if re-

quired.

Push the release lever (23) back and guide the router as far

as it will go in the direction of the base plate (13). Let go of

the release lever (23) again in order to lock the plunging

depth.

Loosen the fastening screws (44) approx. two turns so that

the guide plate (11) is freely movable.

Insert the centring pin (45) into the tool holder as shown in

the figure. Hand-tighten the cap nut so that the centring pin

can still be moved freely.

Align the centring pin (45) and the guide bushing (43) to

each other by slightly moving the guide plate (11).

Retighten the fastening screws (44).

Remove the centring pin (45) from the tool holder.

Push the release lever (23) and guide the router to the up-

permost position.

Changing the Battery (GOF 1250 LCE) (see figure M)

Slide the battery compartment cover (22) upwards and re-

move the battery. Insert a new battery (type CR2032). The

positive pole of the battery must point forwards to the bat-

tery compartment cover (22). Insert the seal (46) and close

the battery compartment cover (22).

Maintenance and Service