Inhoudsopgave
Advertenties
5.1 Safety guard (Fig. 2/Item 15)
•
The safety guard (15) protects the user from
accidentally touching the saw blade (12) but
still gives you an unobstructed view of the
cutting area.
•
The safety guard (15) must always be fitted
when carrying out cutting work.
•
The safety guard can be removed for carrying
out adjustments.
5.2 Changing the saw blade
(Figs. 3-4/Item 12)
Danger!
•
You can fit or replace saw blades without
using any other tools.
•
Pull out the mains plug before you fit or repla-
ce a saw blade.
•
Set the selector switch for pendulum action
(8) to position A (see Fig. 15).
•
The teeth of the saw blade are very sharp!
•
Remove the safety guard (15).
•
Press the blade holder (14) and insert the
saw blade (12) into the blade holder (14) as
far as the stop (Fig. 3). The teeth on the saw
blade must be pointing forwards.
•
Allow the saw blade holder (14) to slide back
into position. The saw blade (12) must sit in
the guide roller (10) (Fig. 4).
•
Check that the saw blade (12) is securely
mounted in the blade holder.
•
To remove the saw blade, follow the instruc-
tions above in reverse order.
5.3 Fitting the parallel stop (Fig. 5/Item 11)
•
The parallel stop (11) enables you to saw
parallel cuts.
•
Undo the two locking screws for the parallel
stop (13) on the soleplate (7).
•
Now slide the parallel stop into the guides on
the soleplate (7). You can fit the parallel stop
(11) on either the left or right of the equip-
ment.
•
The guide strip must always face downwards.
Set the required distance using the measu-
rement scale on the parallel stop (11) and
tighten the locking screws for the parallel stop
(13) again.
5.4 Setting the soleplate for miter cuts (Fig. 6)
•
Use the hexagon key (21) to loosen the
screws for the soleplate (16) on the bottom of
the adjustable soleplate (7) (Fig. 6).
•
Pull the soleplate (7) forwards slightly. The so-
leplate can now be swiveled a maximum 45°
to the left and right.
Anl_TC_JS_90_SPK13.indb 18
Anl_TC_JS_90_SPK13.indb 18
GB
•
If the soleplate (7) is pushed back to the
tear again it will only function in the locking
positions at 0°, 15°, 30° and 45°, which are
marked on the graduated scale for the sole-
plate (9). Move the soleplate into the required
position and refasten the screw securing the
soleplate (16).
•
However, the soleplate (7) is also easily set to
another angle. To do so, move the soleplate
(7) to the front, set the desired angle and re-
fasten the screw securing the soleplate (16).
Important! For miter cuts you must remove the
locking screws for the parallel stop (13) and the
splinter guard (17).
5.5 Adapter for chip extraction system
(Fig. 7/Item 5)
•
Connect your jigsaw to a vacuum cleaner
using the adapter for dust extraction (5). This
will ensure optimum chip extraction from the
workpiece. The benefits are that you will pro-
tect both the equipment and your own health.
Your work area will also be cleaner and safer.
•
Dust created when working may be dange-
rous. Refer to the section entitled "Safety
information".
•
Fit the adapter for chip extraction (5) as
shown in Fig. 7. The adapter for chip extrac-
tion (5) must audibly engage to ensure that it
is secure in the soleplate (7). The adapter for
chip extraction (5) cannot be used for miter
cuts.
•
Fit the vacuum tube of the vacuum cleaner
onto the opening of the adapter for chip ex-
traction (5). Check that the connections are
air-tight.
5.6 Line guide (Fig. 10-12/Item 18)
Using the line guide (18) you can carry out exact
cuts following cutting lines marked on the workpi-
ece. Fit the line guide by mounting it on the top of
the soleplate (7) and letting it lock in place at the
bottom, as shown in Fig. 10. Use the mark (b) for
the 0° angle setting (Fig. 11) and the mark (c) for
the 45° angle setting (Fig. 12). See point 5.4 for
information about the angle setting.
Notice! Carry out a trial cuts in a piece of
waste wood.
5.7 Splinter guard (Fig. 6/Item 17)
The splinter guard ensures that the material you
want to cut does not splinter or crack during sa-
wing. Insert it into the soleplate from underneath
as shown in Fig. 10.
- 18 -
11.12.2024 13:14:35
11.12.2024 13:14:35
Advertenties
Inhoudsopgave
