Advertenties
To use the SavE
The product has a battery saving function (SavE
gives longer operation time.
™
•
Push the SavE
button to position 1 to start the
function. (Fig. 35)
™
•
Push the SavE
button to position 0 to stop the
function.
Note:
™
The SavE
function stops automatically if the
ground conditions make it necessary to have a higher
™
output. The SavE
function starts automatically again
when the ground conditions let it.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
Motor stalling
During operation, the blade and motor can temporarily
stop because of obstacles such as grass blockage
below the cutting cover. If this occurs and you keep the
motor brake handle pushed down, the product restarts
automatically. If the product does not restart in 5-10
seconds, it can be necessary to clean below the cutting
To clean the product on page 17 .
cover. Refer to
WARNING:
product tries to restart automatically for 5-10
seconds. Wait for a minimum of 15 seconds
before you do a check of the cutting cover.
WARNING:
cutting cover, release the motor brake
handle, turn the safety key to 0, remove
the battery and wait for a minimum of
5 seconds. There is a risk of injury if
the obstacle is removed and the product
accidentally starts.
To stop the product
WARNING:
before you let the product out of view.
1. Release the motor brake handle to stop the motor.
(Fig. 36)
Note:
For LC 251iS. To stop the drive of the
wheels, release the drive bail.
2. Open the battery lid and turn the safety key to 0.
(Fig. 37)
3. To remove the battery, push the 2 release buttons
and pull out the battery. (Fig. 38)
16
™
function
If the motor stops, the
Before a check of the
Turn the safety key to 0
4. Charge the battery if it is weak. For more
information, refer to
™
) that
15 .
To use the product with the grass
catcher
1. Lift the rear cover. (Fig. 39)
2. Put the grass catcher on the bracket.
3. Release the rear cover and put it on top of the grass
bag frame. (Fig. 40)
To change the product to side
discharge mode
1. Lift the rear cover and remove the grass bag, if it is
installed.
2. Close the rear cover and make sure that it is tightly
closed against the product.
3. Lift the discharge lock. (Fig. 41)
4. Open the side discharge cover and install the side
discharge deflector onto the support pins. (Fig. 42)
5. Let the side discharge cover close against the
side discharge deflector. Make sure that the side
discharge deflector is tightly in position before you
operate the product.
To empty the grass catcher
1. Lift the grass catcher with the frame handle.
2. Use the frame handle and the bag handle when you
empty the grass catcher. (Fig. 43)
To get a good result
•
Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
•
Do not cut more than ⅓ of the length of the grass.
Use the highest cutting height when you start to cut
the grass. Examine the result and lower the cutting
height to an applicable level. If the grass is very long,
operate slowly and cut 2 times if it is necessary.
•
Cut in different directions each time to prevent
stripes in the lawn.
•
Lift the rear cover and remove the grass catcher.
•
If a mulch plug and a mulch blade are attached,
remove them.
To charge the battery on page
WARNING:
Do not operate the product
without a grass catcher installed or without
the rear cover closed. Objects can eject and
cause injury to the operator.
CAUTION:
Lift the grass catcher when
you move it to prevent wear.
2207 - 004 - 03.11.2023
Advertenties
