Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
to its use, refer to the relative instruction manual;
- in case of supply from a water tank, introduce the suction hose inside the tank and make sure the vertical
distance between the water level and the pump is no more than 1.5 m (4.9 ft).
• Make sure the master switch (1) is on "0" position and insert the plug.
• Move the master switch (1) to position "1".
• Press the spray gun lever (17) and wait for a continuous jet of water to come out;
• Move the master switch (1) to "0" position and connect the lance hose (14) to the spray gun (13),
tightening well.
• Make sure the nozzle holder head (15) is not in the detergent dispensing position (refer to
WITH DETERGENT"
• Start the high-pressure cleaner again moving the master switch (1) to position "1".
• Press the gun spray lever (17), making sure the spray of the nozzle is even and this is not dripping.
• If necessary, adjust the pressure by turning the knob (6). Turn clockwise to increase pressure,
anticlockwise to decrease it.
• The pressure value can be modified by acting on the pressure regulator (45) of the cleaner gun (13), as in
h
. 3 to increase the pressure, or as in
In FIg
• You can check the pressure level on the pressure gauge (34).
The detergents recommended by the Manufacturer are over 90% biodegradable.
For instructions on how to use them, refer to the indications on the label of the detergent pack.
• Move the master switch (1) to "0" position.
• Check if the pressure regulator (45) is set for maximum pressure.
• In the case of suctioning from the high power cleaner's tank (40), remove the cap (39) and, being careful
not to spill any liquid (maximum capacity is 3.5 l/0.92 US gal), fill the tank with the solution wanted.
• To ensure thorough cleaning, the detergent tank (40) can be taken out after releasing it by turning the
device (41) anticlockwise.
• In the case of suctioning from an external tank (
the coupling (43) the connection (25) of the detergent suction hose (23) from external tank as shown
in
. 7 -
FIg
rEFErEncE
which you have already prepared with the detergent solution wanted: in this case too, follow the
indications given for the dosage on detergent pack label.
• Operate on the nozzle holder head (15) as shown in
• Start the high-pressure cleaner again, moving the master switch (1) to position "1" and operate the
lever (17): suction and mixing occur automatically as the water flows through.
• Turn the knob of the detergent tank cap (39) until the quantity of product wanted is dispensed.
• To stop the supply of detergent and restore high-pressure operation, stop the high-pressure cleaner
moving the master switch (1) to "0" position and operate on the head (15) as shown in
• Release the cleaner gun lever (17) to stop the high pressure jet; the high pressure cleaner moves to
the by-pass operating mode and stops immediately (K250 TSI models only), or after approximately 13
seconds it remains in this state (K250 TSR models only).
• The cleaner will resume normal operation the as soon as the lever on the gun is pressed.
WARNING
• If you stop the high pressure jet and put the gun down, enable the locking handle (16).
• Completely close the water supply tap (or remove the suction hose from the water tank).
• Empty the water from the high-pressure cleaner, allowing this to operate for a few seconds with the
spray gun lever (17) pressed.
24
• Move the master switch (1) to "0" position.
E
. 5.
opEratIon
In FIg
STANDARD OPERATION (HIGH PRESSURE)
paragraph).
OPERATION WITH DETERGENT
n
opEratIon
"b"
; put the other end of the hose (23), including the filter (24), in the external tank
STOPPING OPERATION
l
. 3 to decrease the pressure (Extra TSR only).
stEp
In FIg
. 7
. Proceed in the opposite order to put it back in place.
oF FIg
. 7 -
FIg
rEFErEncE
. 3 -
FIg
STOP
I
opEratIon
h
. 3 (Extra TSR only).
stEp
In FIg
"a"),
remove the cap (44) and put in
"a"
.
rEFErEncE
M
. 6.
opEratIon
In FIg
. 5.
In FIg
"OPERATION
stEp
.
. 3 -
" b"
FIg
rEFErEncE
s
. 3.
stEp
In FIg
Advertenties
Inhoudsopgave
