Advertenties
Beschikbare talen
Beschikbare talen
10. Measuring point illumination (figure J)
-
The measuring point illumination
with the probe tips being open by actuating the push-but-
6
ton
of the display handle L2
- The off automatically after 10 seconds.
11. Battery replacement (figure K)
-
Do not apply voltage to the device when the battery com-
partment is open!
-
The battery compartment is located on the back of the dis-
play handle L2
- Unscrew the screw of the battery compartment cover
and replace the used batteries by two new micro batter-
ies (LR03/ AAA). Make sure that the new batteries are
inserted with correct polarity!
- Place the battery compartment cover onto the display han-
8
dle L2
12. Technical data
- regulation: DIN EN 61243-3: 2011, IEC 61243-3: 2009
- nominal voltage range: 12 V to 1,000 V AC / DC
- nominal frequency range f: 0 to 500 Hz
-
max. indication error: U
- internal resistance of measuring circuit: 175 kΩ,
-
current consumption of measuring circuit: I
(1.000 V)
-
current consumption of load circuit: I
- polarity indication: + 24 V LED, - 24 V LED, + 12 V LED, -
12 V LED (with push-buttons being actuated)
- polarity indication: +12 V LED, -12 V LED
-
external conductor (phase) test and phase sequence test:
≥ U
230 V, 50/60 Hz
n
- continuity test: 0 to 100 kΩ, LED + buzzer, testing current:
max. 10 μA
- cable break detector: ≥ U
- vibration motor, start: ≥ U
- overvoltage category: CAT IV 600 V, CAT III 1,000 V
-
protection category: IP 65 (DIN VDE 0470-1 IEC/ EN 60529)
6 - first index: protection against access to dangerous
parts and protection against solid impurities, dustproof
5 - second index: protected against water jets. The device
can also be used in the rain.
- max. allowable Duty cycle: 30 s (max. 30 seconds), 240 s
off
- battery: 2 x micro, LR03/AAA (3 V)
-
weight: approx. 250g
-
length of connecting cable: approx. 1,000 mm
-
operating temperature and storage temperature range:
- 15 °C to + 55 °C (climatic category N)
-
times of controlled reduction (thermal protection):
voltage/time: 230 V/30 s, 400 V/9 s, 690 V/5 s, 1000 V/2 s
- response time of the display: 750 ms
13. General maintenance
Clean the exterior of the device with a clean dry cloth.
If there is contamination or deposits in the area of the battery
or the battery housing, clean these areas as well by means
of a dry cloth.
If the device is stored for a longer period of time, remove the
batteries from the device!
14. Environmental protection
Please lead batteries and also the device at the end
of its useful life to the available return and collection
systems
DUSPOL
Avant d'utiliser le contrôleur de tension DUSPOL
Lisez le mode d'emploi et tenez impérativement compte des
consignes de sécurité !
Table des matières
1.
Consignes de sécurité
2.
Description de l'appareil
3.
4.
5.
6.
7.
8.
9.
1.
Consignes de sécurité :
-
Pendant le contrôle, ne touchez l'appareil qu'aux poignée
isolées L1
d'essai L1/-
-
Contrôlez toujours le bon fonctionnement du contrôleur de
tension immédiatement avant et après de l'utiliser ! (voir
paragraphe 3). Le contrôleur de tension ne doit être utilisé
dès lors qu'une ou plusieurs affichages ne fonctionnent
plus ou dès lors l'appareil n'est plus opérationnel !
-
Le fonctionnement du contrôleur de tension est restreint si
les piles sont vides ! Il est possible d'effectuer un contrôle
de tension au moyen de l'affichage de niveau par LED
à partir d'une tension ≥ 50 V AC/DC même sans piles.
-
Le contrôleur de tension ne doit être utilisé que dans la
plage de tension nominale spécifiée et dans les installa-
03/2013
8
.
and tighten the screw.
Mode d'emploi
7
8
et L2
2
et L2/+
DUSPOL
F
4
8
(1 second).
±15%, ELV U
n
200 V
n
230 V
n
expert 1000
®
et ne touchez jamais les pointes
3
!
expert 1000
®
can be switched on
+0% -15%
n
< 6,0 mA
S
< 550 mA (1,000 V)
S
expert 1000:
®
9
8
Advertenties
Hoofdstukken
